Ferroli AquaSol Installation & User Manual Download Page 21

Page: 21 / 24

M 1261-06-X AquaSol Ferroli Installation Manual.doc

July 2006

Page 21 of 24

10.

Differential Temperature Controller

Optimum performance of the solar system is assured by the DT3 controller. The unit

is fully automatic and will start the solar circulating pump when the solar collector is
10°C hotter than the lower part of the AquaSol cylinder.

When the temperature difference falls to 2°C the pump will switch off. Upon

starting, the pump will automatically run on high speed (power consumption 80
watts) for a period of 400 seconds, following which it will switch to solar radiation

dependent lower speed.
The pump will be switched off as the AquaSol reaches a temperature of 85°C. After

this the collector circuit will drain and prevent the AquaSol from overheating.

10.1

Fault finding errors

In the event of a malfunction, flashing error codes will be displayed.

Codes 71 – 73 inclusive are low priority

Codes 74 – 77 inclusive are high priority

Error codes are automatically reset once the mains supply is isolated.

Start

Indication pump on

Tcoll-storage>10C

Tstorage<85

Tcoll-Tstorage

Is the pump on?

Pump to low power

Pump on. 400s high power

Tcoll-Tstorage>2C

Indication pump off

Pump off

Normal

eration

Summary of Contents for AquaSol

























Search results

Summary of Contents for AquaSol

Reviews:

Related manuals for AquaSol

Brands by name

Popular brands

Ferroli AquaSol, Installation & User Manual

Search results

Summary of Contents for AquaSol

Reviews:

Related manuals for AquaSol

Brands by name

Popular brands