Ferris 5901914 Operator'S Manual Download Page 9

Not for 

Reproduction

9

may suddenly appear in the mowing area for another ride

and be run over or backed over by the machine.

• Never allow children to operate the unit.
• Use extra care when approaching blind corners, shrubs,

trees, or other objects that may obscure vision.

Emissions

• Engine exhaust from this product contains chemicals

known, in certain quantities, to cause cancer, birth

defects, or other reproductive harm.

• Look for the relevant Emissions Durability Period and Air

Index information on the engine emissions label.

Service and Maintenance

To avoid personal injury or property damage, use extreme

care in handling gasoline. Gasoline is extremely flammable

and the vapors are explosive. 

Safe Handling of Gasoline

 

• Extinguish all cigarettes, cigars, pipes, and other sources

of ignition. 

• Use only approved gasoline containers. 
• Never remove the gas cap or add fuel with the engine

running. Allow the engine to cool before refueling. 

• Never fuel the machine indoors. 
• Never store the machine or fuel container where there is

an open flame, spark, or pilot light such as near a water

heater or other appliance. 

• Never fill containers inside a vehicle or on a truck bed

with a plastic bed liner. Always place containers on the

ground away from your vehicle before filling. 

• Remove gas-powered equipment from the truck or

trailer and refuel it on the ground. If this is not possible,

then refuel such equipment on a trailer with a portable

container, rather than from a gasoline dispenser nozzle. 

• Keep nozzle in contact with the rim of the fuel tank or

container opening at all times until fueling is complete. Do

not use a nozzle lock-open device. 

• If fuel is spilled on clothing, change clothing immediately. 
• Never over-fill the fuel tank. Replace gas cap and tighten

securely. 

• Use extra care in handling gasoline and other fuels. They

are flammable and vapors are explosive. 

• If fuel is spilled, do not attempt to start the engine but

move the machine away from the area of spillage and

avoid creating any source of ignition until fuel vapors

have dissipated. 

• Replace all fuel tank caps and fuel container caps

securely. 

Maintenance and Storage

 

• Always observe safe refueling and fuel handling practices

when refueling the unit after transportation or storage. 

• Always follow the engine manual instructions for storage

preparations before storing the unit for both short and

long term periods. 

• Always follow the engine manual instructions for proper

start-up procedures when returning the unit to service. 

• Never store the machine or fuel container inside where

there is an open flame, such as in a water heater. Allow

unit to cool before storing. 

• Shut off fuel while storing or transporting. Do not store

fuel near flames or drain indoors. 

• Keep all hardware, especially blade attachment bolts,

tight and keep all parts in good working condition.

Replace all worn or damaged decals. 

• Never tamper with safety devices. Check their proper

operation regularly. 

• Disengage drives, lower implement, set parking brake,

stop engine and remove key or disconnect spark plug

wire. Wait for all movement to stop before adjusting,

cleaning or repairing. 

• Clean grass and debris from cutting units, drives,

mufflers, and engine to prevent fires. Clean up oil or fuel

spillage. 

• Let engine cool before storing and do not store near

flame. 

• Stop and inspect the equipment if you strike an object.

Repair, if necessary, before restarting. 

• Park machine on level ground. Never allow untrained

personnel to service machine. 

• Use jack stands to support components when required. 
• Carefully release pressure from components with stored

energy. 

• Disconnect battery or remove spark plug wire before

making any repairs. Disconnect the negative terminal

first and the positive last. Reconnect positive first and

negative last. 

• Use care when checking blades. Wrap the blade(s) or

wear gloves, and use caution when servicing them. Only

replace blades. Never straighten or weld them. 

• Keep hands and feet away from moving parts. If possible,

do not make adjustments with the engine running. 

• Charge batteries in an open well ventilated area, away

from spark and flames. Unplug charger before connecting

or disconnecting from battery. Wear protective clothes

and use insulated tools. 

• Grass catcher components are subject to wear, damage,

and deterioration, which could expose moving parts or

allow objects to be thrown. Frequently check components

and replace with manufacturer’s recommended parts,

when necessary. 

• Check brake operation frequently. Adjust and service as

required. 

• Use only factory authorized replacement parts when

making repairs. 

• Always comply with factory specifications on all settings

and adjustments. 

• Only authorized service locations should be utilized for

major service and repair requirements. 

• Never attempt to make major repairs on this unit unless

you have been properly trained. Improper service

procedures can result in hazardous operation, equipment

damage and voiding of manufacturer’s warranty. 

Summary of Contents for 5901914





































Reviews: