manualshive.com logo in svg

Ferris 46764, Operator'S Manual, Page: 20 / 34

Share
Download
Ferris 46764 Operator'S Manual Download Page 20

14

04

3-Bag Hood & Mount Installation

A

Figure 22. Install Mount Plate
(Ferris 1000Z & IS1000Z Series and Derby Colts)

A.

Rear Shield

F.  3/8-16 Flange Nut

B.

3/8-16 x 1” Bolt

G.  3/8-16 x 2-1/2” Bolt

C.

Mount Plate

H.  Bar Clamp

D.

Mount Spacer

I.   3/8-16 Nylon Lock Nut

E.

Mount Support (1/4” Thick)

J.  3/8-16 x 2” Bolt

Install Mount Plate

(Ferris 1000Z & IS1000Z Series and Derby Colt “T”
Series)

1. Remove the lower bolts, washers & nuts from the

rear shield (A, Figure 22).

2. Remove the lower bolts, washers & nuts (circled)

from the bumper of the 1000Z 61”, IS1000Z 52”
models and Derby Colt ZT2352T only.

NOTE:  Use caution when removing the lower bolts,
they are used to secure counterweights to the inside of
the bumper.

3. Install the mount plate (C) and mount support (E) on

the lower bumper and secure with the 3/8-16 x 1”
bolts (B) and 3/8-16 flange nuts (F) as shown.  Use
3/8-16 x 2” bolts (J) and 3/8-16 flange nuts (F) for
1000Z 61”,  IS1000Z 52” models and Derby Colt
ZT2352T.  Reinstall the counterweights at this time.

NOTE:  The mount support (E) is only used with the
1000Z 48” & 52” models, IS1000Z 48” model and Derby
ZT2148T model.

4. If required, use the lower mount holes as a guide,

drill through the bumper with a 3/8” drill bit.

5. Install the mount spacer (D) in between the bumper

and mount plate and secure with the 3/8-16 x 1”
bolts (B) and 3/8-16 flange nuts (F) as shown.  Use
3/8-16 x 2” bolts (J) and 3/8-16 flange nuts (F) for
1000Z 61” & IS1000Z 52” models and Derby Colt
ZT2352T.

Install Mount Plate

(Derby Colts)

1. Install the mount plate (C, Figure 22) on the bumper

using three bar clamps (H), six 3/8-16 x 2-1/2 bolts
(G) and 3/8-16 nylon lock nuts (I).  Make sure the
top right bolts (circled) are on the inside of the verti-
cal bumper tube.  Push the mount towards the right
until the top right bolts rest against the vertical
bumper tube and tighten securely.

F

E

D

C

H

H

H

C

I

I

I

G

G

G

J

J

B

B

Summary of Contents for 46764



































Reviews:

No comments