Ferris 46764 Operator'S Manual Download Page 34 | Manualshive

Page: 34 / 34

background image

Discharge Chute Reattachment

MOWING WITHOUT THE BLOWER

For operation without the blower, the deflector must be
properly installed in the down position and retained by
the spring latch (Derby models only).

To remove the blower, reverse the installation steps.

Reattaching the Discharge Chute

See Figure 48. Using the retainer pin and hair pin clip,
secure the discharge chute to the mower deck. Make
sure the chute mount tabs are in front of the tabs on the
mower deck. For the Derby mowers, you must also
reinstall the torsion springs and spacer to properly retain
the discharge chute.

Figure 48. Discharge Chute Reattachment

A.

Discharge Chute

B.

Retainer Pin

C.

Hair Pin Clip

D.

Torsion Spring (Derby only)

E.

Spacer (Derby only)

A

B

C

D

E

D

28

00

«
...
32
33
34

Summary of Contents for 46764



































Reviews:

No comments

Related manuals for 46764

Brand: ECLOZ Pages: 56

Brand: Yard Machines Pages: 20

Brand: Toro Pages: 52

Brand: Toro Pages: 32

30710 Groundsmaster 300

Brand: Toro Pages: 20

Greensmaster 3150 04358

Brand: Toro Pages: 48

Brand: Lastec Pages: 51

Brand: Simplicity Pages: 4

Brand: Dixon Pages: 44

Brand: Qualcast Pages: 2

Brand: Bestgreen Pages: 10

Brand: Lux Tools Pages: 148

Brand: Zoef Robot Pages: 54

Brand: Nakayama Pages: 80

Brand: Swisher Pages: 38

Brand: Husqvarna Pages: 50

Brand: Husqvarna Pages: 78

Brand: OHIOSTEEL Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands