Ferimex E-4000 User Manual Download Page 4

Page: 4 / 23

Front panel description

All the connectors and switches are mounted on the front panel.

- RS232

9pin M

connector for connecting null modem serial cable

- ETH0-ETH3

RJ45 F

ethernet connectors

- POWER

power supply connector

Connecting the device to the ethernet

The device could be connected to the ethernet either through a hub (resp. switch) or
directly to the other computer (resp. traffic manager). When connecting to the
hub/switch, use a straight cable as follows:

8 pin RJ45 connector

pin 1

pin 2

pin 3

pin 4

pin 5

pin 6

pin 7

pin 8

When connecting directly to the other computer or traffic manager, use the crossed-
over cable with following pinout:

8 pin RJ45 connector

pin 1

pin 3

pin 2

pin 6

pin 3

pin 1

pin 4

pin 7

pin 5

pin 8

pin 6

pin 2

pin 7

pin 4

pin 8

pin 5

TRAFFIC MANAGER E-4000

Summary of Contents for E-4000
























Search results

Summary of Contents for E-4000

Reviews:

Related manuals for E-4000

Brands by name

Popular brands

Ferimex E-4000, User Manual

Search results

Summary of Contents for E-4000

Reviews:

Related manuals for E-4000

Brands by name

Popular brands