12
en
For your safety.
Read all safety warnings and all instruc-
tions.
Failure to follow the warnings
and instructions may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
Do not use this power tool before you have thor-
oughly read and completely understood this
Instruction Manual and the enclosed “General
Safety Instructions” (document number
3 41 30 054 06 1). The documents mentioned should be
kept for later use and enclosed with the power tool,
should it be passed on or sold.
Please also observe the relevant national industrial safety
regulations.
Intended use of the power tool:
This power tool, as a hand-guided straight grinder, is
intended for dry grinding/roughing and cutting of metal
and stone in weather-protected environments using the
application tools and accessories recommended by FEIN.
The high-frequency power tool may only be operated
with 3-phase alternating current with the frequency
stated in the Specifications.
Safety warnings common for sanding, sanding with
sanding sheets, working with wire brushes,
polishing and cut-off grinding
This power tool is intended to function as a grinder, sander,
wire brush or cut-off tool. Read all safety warnings, instruc-
tions, illustrations and specifications provided with this
power tool.
Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury.
This power tool is not recommended for polishing.
Opera-
tions for which the power tool was not designed may
create a hazard and cause personal injury.
Do not use accessories which are not specifically designed
and recommended by the tool manufacturer.
Just because
the accessory can be attached to your power tool, it does
not assure safe operation.
The rated speed of the accessory must be at least equal to
the maximum speed marked on the power tool.
Accessories
running faster than their rated speed can break and fly
apart.
The outside diameter and the thickness of your accessory
must be within the capacity rating of your power tool.
Incorrectly sized accessories cannot be adequately
guarded or controlled.
The arbor size of wheels, flanges, backing pads or any other
accessory must properly fit the spindle of the power tool.
Accessories with arbor holes that do not match the
mounting hardware of the power tool will run out of bal-
ance, vibrate excessively and may cause loss of control.
Do not use a damaged accessory. Before each use inspect
the accessory such as abrasive wheels for chips and
cracks, backing pad for cracks, tear or excess wear, wire
brush for loose or cracked wires. If power tool or accessory
is dropped, inspect for damage or install an undamaged
accessory. After inspecting and installing an accessory,
position yourself and bystanders away from the plane of the
rotating accessory and run the power tool at maximum no-
load speed for one minute.
Damaged accessories will nor-
mally break apart during this test time.
Wear personal protective equipment. Depending on appli-
cation, use face shield, safety goggles or safety glasses. As
appropriate, wear dust mask, hearing protectors, gloves
and workshop apron capable of stopping small abrasive or
workpiece fragments.
The eye protection must be capable
of stopping flying debris generated by various operations.
The dust mask or respirator must be capable of filtrating
particles generated by your operation. Prolonged expo-
sure to high intensity noise may cause hearing loss.
Character
Unit of measure,
international
Unit of measure,
national
Explanation
n
/min
rpm
Rated speed
V
V
Rated voltage
P
1
W
W
Power input
P
2
W
W
Output
f
Hz
Hz
Frequency
M…
mm
mm
Size of metric thread
L
wA
dB
dB
Sound power level
L
pA
dB
dB
Sound pressure level
L
pCpeak
dB
dB
Peak sound pressure level
K…
Uncertainty
m/s
2
m/s
2
Vibration emission value (triax vector sum) deter-
mined according to EN 60745
m/s
2
m/s
2
Mean vibrational value for angle grinding
m/s
2
m/s
2
Mean vibrational value for sanding with sanding
sheet
m, s, kg, A, mm, V,
W, Hz, N, °C, dB,
min, m/s
2
m, s, kg, A, mm, V,
W, Hz, N, °C, dB,
min, m/s
2
Basic and derived units of measure from the inter-
national system of units
SI
.
h,AG
h,DS
WARNING
3 41 00 645 06 6.book Seite 12 Donnerstag, 18. November 2010 11:04 11
