Fein MOtlx 6-25, User Manual

Page: 12 / 70

12
en
For all work or when changing application tools, always
wear protective gloves.
Danger of injury from the sharp
edges of the application tools. Application tools can
become very hot while working. Danger of burns!
Never direct the application tool against yourself. Hold the
pneumatic tool in such a manner that the application tool
cannot come into contact with your hand.
Hand/arm vibrations.
Whilst working with this power tool, hand/arm vibra-
tions will occur.
Adopt the correct working practices in order to reduce
the exposure to vibration:
– in the case of strong vibration, take the recommended
work breaks or change your task more frequently,
– keep your hands warm,
– whilst working, only grip the power tool as firmly as
necessary,
– work only with technically sound machines and appli-
cation tools,
– use the FEIN vibration-absorbing, gel working gloves,
If these recommendations are not observed, the expo-
sure to strong vibration during daily work over a longer
period of time can be detrimental to health.
The maximum exposure values stipulated in the indus-
trial safety directives (e. g. in directive 2002/44/EC, a
maximum daily exposure limit of 5 m/s
2
relating to a
normal duration of 8 hours) must not be exceeded.
The value of the estimated weighted acceleration
obtained in the laboratory can serve for predicting the
exposure to vibration. During work, weighted accelera-
tions will be dependent on the particular application, and
deviation from this laboratory value can occur.
Emission values for sound and vibration
(Two-figure – specifications as per ISO 4871)
* These values are based on a work cycle consisting of
no-load and full-load operation of the same duration.
Intended use of the pneumatic tool.
hand-guided pneumatic tool for commercial use, for cut-
ting plastic beads and similar materials, particularly for
cutting out windscreens, rear and side window panes for
the automobile workshop using the application tools and
accessories recommended by FEIN.
Connection to air supply.
For trouble-free operation of the air tool, use a filter/reg-
ulator-lubricator consisting of water separator, oil lubri-
cator and compressed-air regulator.
Check that the pressure in the compressed-air supply
conforms with the pressure given on the rating plate on
the pneumatic tool.
➤
Before connecting, blow through the hose.
The hose should have a minimum diameter of 16 mm.
The opening of the valve and the coupling should have a
diameter of at least 8
mm.
Operating instructions.
When uncoupling hose couplings, first shut the ball valve,
then actuate the pneumatic tool, and then uncouple. Do
not uncouple the hose coupling until after the com-
pressed air has been completely relieved.
Repair and customer service.
Maintain and clean the pneumatic tool every 300 work
hours or every 6 months.
When the pneumatic tool's hose is damaged, it must be
replaced with a specially prepared hose, available from
your FEIN customer service agent.
If required, you can change the following parts yourself:
Application tools, Hose
Warranty and liability.
The warranty for the product is valid in accordance with
the legal regulations in the country where it is marketed.
In addition, FEIN also provides a guarantee in accordance
with the FEIN manufacturer’s warranty declaration.
The delivery scope of your pneumatic tool may include
only a part of the accessories described or shown in this
instruction manual.
Declaration of conformity.
FEIN declares itself solely responsible for this product
conforming with the documents and standards given on
the last page of this Instruction Manual.
Environmental protection, disposal.
Packaging, worn out pneumatic tools and accessories
should be sorted for environment-friendly recycling.
Vibration
Classification of FEIN
application tools according
to vibration class Weighted acceleration*
VC0 < 2.5 m/s
2
VC1 < 5 m/s
2
VC2 < 7 m/s
2
VC3 < 10 m/s
2
VC4 < 15 m/s
2
VC5 > 15 m/s
2
3 41 01 101 06 0.book Seite 12 Freitag, 4. April 2008 8:33 08