4
f)
Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g)
Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into
account the working conditions and the work to be performed.
Use of the power tool for operations
different from those intended could result in a hazardous situation.
5)
Service
a)
Have your power tool serviced by a qualified repair person using only identical replacement parts
.
This will ensure that the safety of the power tool is maintained.
Safety instructions for all operations
Safety Warnings Common for Grinding, Sanding, Wire Brushing, Polishing or Abrasive
Cutting-Off Operations
a)
This power tool is intended to function as a grinder or cut-off tool. Read all safety warnings,
instructions, illustrations and specifications provided with this power tool.
Failure to follow all
instructions listed below may result in electric shock, fire and/or serious injury.
b)
Operations such as sanding, wire brushing or polishing are not recommended to be performed with
this power tool.
Operations for which the power tool was not designed may create a hazard and cause
personal injury
c)
Do not use accessories which are not specifically designed and recommended by the tool
manufacturer.
Just because the accessory can be attached to your power tool, it does not assure safe
operation.
d)
The rated speed of the accessory must be at least equal to the maximum speed marked on the power
tool.
A
ccessories running faster than their rated speed can break and fly apart.
e)
The outside diameter and the thickness of your accessory must be within the capacity rating of your
power tool.
Incorrectly sized accessories cannot be adequately guarded or controlled.
f)
Threaded mounting of accessories must match the grinder spindle thread. For accessories mounted
by flanges, the arbour hole of the accessory must fit the locating diameter of the flange.
Accessories
that do not match the mounting hardware of the power tool will run out of balance, vibrate excessively and
may cause loss of control.
g)
Do not use a damaged accessory. Before each use inspect the accessory such as abrasive wheels for
chips and cracks, backing pad for cracks, tear or excess wear, wire brush for loose or cracked wires.
If power tool or accessory is dropped, inspect for damage or install an undamaged accessory. After
inspecting and installing an accessory, position yourself and bystanders away from the plane of the
rotating accessory and run the power tool at maximum no-load speed for one minute.
Damaged
accessories will normally break apart during this test time.
h)
Wear personal protective equipment. Depending on application, use face shield, safety goggles or
safety glasses. As appropriate, wear dust mask, hearing protectors, gloves and workshop apron
capable of stopping small abrasive or workpiece fragments.
The eye protection must be capable of
stopping flying debris generated by various operations. The dust mask or respirator must be capable of
filtrating particles generated by your operation. Prolonged exposure to high intensity noise may cause hearing
loss.
i)
Keep bystanders a safe distance away from work area. Anyone entering the work area must wear
personal protective equipment.
Fragments of workpiece or of a broken accessory may fly away and cause
injury beyond immediate area of operation.
j)
Hold the power tool by insulated gripping surfaces only, when performing an operation where the
cutting accessory may contact hidden wiring or its own cord.
Cutting accessory contacting a "live" wire
may make exposed metal parts of the power tool "live" and could give the operator an electric shock.
k)
Position the cord clear of the spinning accessory.
If you lose control, the cord may be cut or snagged and
your hand or arm may be pulled into the spinning accessory.
l)
Never lay the power tool down until the accessory has come to a complete stop.
The spinning
accessory may grab the surface and pull the power tool out of your control.
m)
Do not run the power tool while carrying it at your side.
Accidental contact with the spinning accessory
could snag your clothing, pulling the accessory into your body.
n)
Regularly clean the power tool’s air vents.
The motor’s fan will draw the dust inside the housing and
excessive accumulation of powdered metal may cause electrical hazards.
o)
Do not operate the power tool near flammable materials.
Sparks could ignite these materials.
p)
Do not use accessories that require liquid coolants.
Using water or other liquid coolants may result in
electrocution or shock
