background image

mimclip.mimsafe.com

Wall Kit - 80324

Edition 2020-12

The advantages of the Wall Kit

The advantages of the MIMclip

1.  It has been produced with safety being the first and 

foremost important factor.

2.  Reduces the possibility of rotational falls.
3.  FEI approved number FEI13SWE.
4.  Controlled movement of fence during release.
5.  Reconstruction time is less than 30 seconds.
6.  The parts are made of powder coated steel and can be left 

outside, no maintenance is required.

7.  The very highest quality of product from Sweden ISO 9001.

The MIMclip breaks on impact. The flag is bent 
when the clip is exposed to fatigue. In both cases 
the clip must be replaced. The top section is 
connected to the post with a hinge that makes 
the fence easy to reconstruct. This saves time, 
guarantees fair and correct judging for riders 
and contributes to the overall safety of the 
sport.

200 mm
8 inch

50 mm 

2 inch

IMPORTANT

When top section is released the gap between top section and bottom section 

should be 

maximum 50 mm.

If gap is wider, then place object to shrink/reduce the gap.

When top section is released the distance between top section and ground 

should be 

minimum 200 mm.

 

If distance between ground and top section is less, then place an object which 

will prevent the top section falling into the 

SAFE AREA

The flag is bent when fatigued.

WARNING

To procect the fence mechanism when 

released, put a dampening material 

between  the safe area and the released 

part of the fence.

Summary of Contents for mimsafe 80326
























































Reviews: