background image

SECTION I - BASIC SYSTEM

Model 80K

USED WITH ALL MODELS

Containing electronic components for generating

sounds, the Model 80K amplifier is the basic part

of the siren and common to all models described in

this Manual. It will be found in the same cabinet

with it’s controls or in a separate cabinet remote

from it’s controls.
External Components Include:

a) Park Kill Wire- deactivates siren when

grounded.

b) Power Transistors (Rear) - Electrically

“hot” during Siren/P.A. operation. Contact

with metal objects will destroy them.

c) Fuse (Rear) - In unlikely event of failure,

do not overfuse.

PRECAUTIONS

1. Although the 80K has an extremely wide operating

temperature range (-40F to + 185F), underhood

installation where temperatures exceed 230F is not

advised.

2. Cabinet is not waterproof.

BLOW-OUT PROOF TRANSISTOR PROTECTION

1. Output transistors, blown out in normal sirens by

failures of the siren speaker or its wiring are protected

in the Unitrol 80K by automatic circuitry.

a) Short-circuited speaker or wiring stops

siren sounds.  A soft “popping” noise from

the speaker or amplifier will occur 60 times

per minute.

b) Blown-out speaker (open coil) or

disconnected speaker wire causes amplifier

to emit siren sounds from amplifier but not

from speaker.

c) Primary input voltage above 16Vdc will

cause shutdown of tone generating stages. No

sounds will be emitted by the amplifier or siren

speaker.

2. In all instances, amplifier operation will automatically

resume when the external defect is repaired.

ASSEMBLY METHODS

1. Amplifier can be used with control units as

follows:

a)  Remote - Amplifier is installed

remotely from control unit and

connected by a 4 foot or 15 foot

cable.

b) Single-Unit - Amplifier / control

unit are plugged together and

housed in one cabinet.

Page 1

Summary of Contents for Unitrol 280 Series


















Reviews: