background image

SECTION X - TWO-TONE SYSTEMS

          For Models 280K & 480K

REQUIRED EQUIPMENT

1. Control Unit - Any existing 280K or 480K

control unit can be used. No modifications or

additional switches are required.

2. Amplifiers - Two amplifiers, each housed in a

separate cabinet, are required.

3. Cables - A UMCO30T cable is needed for

interconnecting the two amplifiers. UMCO30K

(4’ or 15’ long) is needed for interconnecting

both amplifiers with the control unit.

4. Siren Speakers - At least one speaker must be

used with each amplifier. Two speakers may be

used as indicated by dotted lines in drawing.

Note: A speaker having one horn, but two driver

units (such as a 200 watt speaker), is electrically

the same as two speakers.

AMPLIFIER INSTALLATION

1. Install first amplifier as indicated in drawing.

2. Set slide switch on bottom of amplifier

chassis to match power rating of speakers

to be used.

3. Install amplifier with 4 inches maximum

between cabinets.

Page 11

PRELIMINARY CONNECTIONS

1. Interconnect AIR HORN wires from both 3 - pin

amplifier connectors using the appropriate

connector.

2. Intrusion Alarm - See Section VIII.

3. Connect one terminal (either one) of one siren

speaker to vehicle chassis (-). Connect same number

terminal of remaining speakers to vehicle chassis(-).

4. Of the two SIREN SPEAKER wires coming

from  the 12-pin control unit pigtail connector,

connect either one to vehicle chassis (-), and the

other to the speaker.

FINAL CONNECTIONS

a) see drawings.

1. The RED primary wire from the added amplifier

must connect directly to the positive (+) battery post

or to an appropriate power distribution terminal.

2. It is vitally important for proper siren operation

that a 12-ga (minimum) “jumper” be placed across the

RED primary wires of each amplifier as indicated.

Summary of Contents for Unitrol 280 Series


















Reviews: