manualshive.com logo in svg

Federal Signal Corporation SS2000+ ? Series, Operation Manual, Page: 39 / 80

Share
Download
Federal Signal Corporation SS2000+ ? Series Operation Manual Download Page 39

39

Using the S Software

Description, Specifications, SS Software, and Operation Manual

 

Federal Signal

 www.fedsig.com

Field

Description

Comment Sent to 

Printer when this 

Function is activated

Enter a description that is sent to the printer during the activation.

Two-Tone

Select TwoTone from Activation Codes to display the Two-Tone group box. To save, click 

Save.

Field

Description

"A" Tone

Enter the tone frequency of the A tone.

"A" Len

Enter the length of the A tone. Duration is in milliseconds.

"B" Tone

Enter the tone frequency of the B tone.

"B" Len

Enter the length of the B tone. Duration is in milliseconds. 

 

Send Times

Select the number of times this codes is sent. Options are from 1 to 3 

times.

DTMF

Select DTMF from Activation Codes to display the DTMF group box. To save, click Save.

Field

Description

DTMF String

Enter the DTMF string that is sent out. The range is from 1 to 12 digits. 

Send Times

Select the number of times this codes is sent. Options are from 1 to 3 

times.

Summary of Contents for SS2000+ ? Series

















































































Reviews:

No comments