Federal Signal Corporation Pathfinder Installation And Maintenance Instructions Manual Download | Manualshive

Page: 31 / 36

background image

Pathfinder

TM

31

CHAPTER 8

Servicing the Pathfinder

Federal Signal recommends that the siren be returned to your local distributor or Federal Signal for

service. External components such as cabling are available as replacement parts (see Table 8.1).

Except for the slide switch in the siren, there are no other user-serviceable parts within the unit. After

servicing the system, test it to ensure that it is operating properly.

Replacing the Slide Switch

The slide switch can be removed from the siren without removing the siren from the vehicle in most

installations.

STATIC SENSITIVE DEVICE — The circuitry of the control head can be damaged

by electrostatic discharge. Follow anti-static procedures removing the slide

switch.

Figure 8.1

Keypad Removal

«
...
29
30
31
32
33
...
»

Summary of Contents for Pathfinder





































Reviews:

No comments

Related manuals for Pathfinder

Brand: Xiaomi Pages: 10

Brand: IDEC Pages: 6

Brand: Neptune Pages: 35

Brand: QBTech Pages: 13

Brand: STEINEL Pages: 24

Brand: Elko Pages: 5

Brand: Wheelock Pages: 10

Brand: Gallagher Pages: 67

Brand: Securiton Pages: 10

Brand: Comtrend Corporation Pages: 64

Brand: Sylvania Pages: 26

Brand: Dante Pages: 40

DCC-700d Series

Brand: D-MAX Pages: 24

Brand: Q-See Pages: 2

Brand: G-Force Pages: 2

Brand: HiLook Pages: 10

Brand: DMP Electronics Pages: 6

Brand: TUYA Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands