manualshive.com logo in svg

Federal Signal Corporation Informer100 Speaker, Description, Specifications, And Installation Manual

Share
Download
Federal Signal Corporation Informer100 Speaker Description, Specifications, And Installation Manual Download Page 25

25

Installation

Description, Specifications, and Installation Manual

 

Federal Signal 

www.fedsig.com

See the following list of Federal Signal AC powered warning lights that may be controlled 

by the IP100:
•  121S Vitalite® Rotating Warning Light
•  225 Electraray® Rotating Warning Light
•  225X Electraray® Hazardous Location Rotating Warning Light
•  371LED Commander® LED Rotating Warning Beacons
•  371LEDX Hazardous Location Commander® LED
•  FB2LED Fireball® LED Warning Light
•  FB2LEDX Fireball Hazardous Location LED Warning Light
•  191XL Hazardous Location Division Listed LED Warning Light
•  225XL Electraray® Hazardous Location LED Flashing Warning Light
•  FB2PST Fireball Strobe Warning Light
•  225XST and 225XST-I Electraray® Hazardous Location Strobe Warning Light
•  151XST Hazardous Location Warning Light

Figure 15 FB2PST Strobe with Informer100 Speaker

Pipe Nipple

1/2" NPT Pipe Nipple,

3" overall length

(Recommended, customer supplied)

Side View

Front View

For a FB2PST Strobe, the following is recommended (customer supplied): 1/2-inch NPT 

Pipe Nipple (3 inches overall length).

Summary of Contents for Informer100 Speaker





























Reviews:

No comments

Brands by name

Popular brands

Load more brands