manualshive.com logo in svg

Federal Signal Corporation IMPAXX Series, Installation And Maintenance Manual

Share
Download
Federal Signal Corporation IMPAXX Series Installation And Maintenance Manual Download Page 3

3

Installation and Maintenance Manual 

Federal Signal

 www.fedsig.com

Contents

Safety Messages..................................................................................... 4
Unpacking the Product .......................................................................... 9
An Overview of the IMPAXX Series LED Light Heads ......................... 9
Installing the IMPAXX Series LED Light Heads ................................. 10
Converting a Light Head from Controller to Follower ....................... 10
Mounting the IMPAXX to a Vehicle ...................................................... 12
Wiring the IMPAXX in the Vehicle ....................................................... 14

Selecting a Flash Pattern ................................................................................ 15

Maintaining the IMPAXX Series LED Light Heads ............................. 17

Cleaning the Light Heads  ...............................................................................17

Getting Technical Support and Service .............................................. 18
Getting Repair Service ......................................................................... 19
Ordering Replacement Parts ............................................................... 19

Summary of Contents for IMPAXX Series





















Reviews:

No comments

Brands by name

Popular brands

Load more brands