background image

4  

 

Model FHL-TAIL Tail Light Flasher

Driver-Side Connections

See Figure 1 on page 5 and make these connections:

1.

  Locate and cut the brake-light wire. 

2.

  Connect the BLUE wire from the flasher to the end of the wire that goes to the brake light.

3.

  Connect the ORANGE wire from the flasher to the end of the brake light wire that goes to the front 

of the vehicle.

4.

  Locate and cut the reverse-light wire. 

5.

  Connect the RED wire from the flasher to the end of the wire that goes to the reverse light.

6.

  Connect the WHITE/RED wire from the flasher to the end of the reverse light wire that goes to the 

front of the vehicle.

Passenger-Side Connections

See Figure 1 on page 5 and make these connections:

1

.  Extend the YELLOW, PINK, WHITE/BLACK and BLACK wires over to the passenger side of the 

vehicle.

2.

  Locate and cut the brake light wire. 

3.

  Connect the YELLOW wire from the flasher to the end of the brake light wire that goes to the brake 

light. 

4.

  Connect the PINK wire from the flasher to the end of the brake light wire that goes to the front of 

the vehicle.

5.

  Locate and cut the reverse-light wire. 

6.

  Connect the BLACK wire from the flasher to the end of the wire that goes to the reverse light. 

7.

  Connect the WHITE/BLACK wire from the flasher to the end of the reverse light wire that goes to 

the front of the vehicle.

NOTE:

 The RED/BLACK wire is the auxiliary output to control the package tray lights. For instruction to 

wire this feature, see page 6.

Power Switch Connection

FUSE PRECAUTION—Do not use a circuit breaker, fusible link, or slow-
blow fuse. Improper fusing can cause equipment failure and damage.

Extend the BROWN wire from the flasher to an installer-supplied powered switch that will turn 
the flasher on and off. To protect the wire between the switch and the flasher, install a fuse holder 
connected to the powered switch with a 1

 

A ATO or smaller fuse. 

15

 

A Fuse Installation

After you complete the wiring, install a 15 A fuse in the fuse holder between the 14 AWG WHITE wire 
extension and the positive post of the battery.

Summary of Contents for FHL-TAIL









Reviews: