Federal Signal Corporation ez1 echo Installation Instructions Manual Download Page 8

 

 

G  indicates suitability for use in the presence of gases

Special conditions for safe use:

 

1.  All terminals, used and unused shall be fully tightened down.

 

2.  The power supplied to this unit from the central control module must not 

exceed 28 Vdc, 100 mA.

Condições especiais para o Uso Seguro: 
1.  Todas as terminais, estejam as mesmas em uso ou não, devem estar 

completamente parafusadas.

2.  A fonte de alimentação conectada a esta unidade desde o módulo de 

controle central não deverá exceder a 28 Vdc, 100 mA.

IV. SERVICE.

 

The Federal factory will service your equipment or provide technical assistance 

with any problems that cannot be handled locally.

 

Any units returned to Federal Signal for service, inspection, or repair must be 

accompanied by a Return Material Authorization.  This R.M.A. can be obtained from a 

local Distributor or Manufacturer’s Representative.

 

At this time a brief explanation of the service requested, or the nature of the mal-

function, should be provided.

 

Address all communications and shipments to:

   

 

 

FEDERAL SIGNAL CORPORATION

 

 

Electrical Products Division

 

 

Service Department

 

 

2645 Federal Signal Drive

 

 

University Park, IL 60484-3167

-6-

Summary of Contents for ez1 echo













Reviews: