background image

Limited Warranty: 

This product’s limited warranty can be found at www.fedsig.com/SSG-Warranty

SAFETY MESSAGES TO INSTALLERS AND USERS

 

: Products should be installed by a licensed electrician and follow 

all safety instructions. Failure to do so may result in property damage, serious injury, or death.

• 

Read and understand all instructions before installing or operating this equipment.

• 

To avoid electrical shock hazards, do not connect wires when power is applied. Failure to observe this warning may 

lead to serious injury or death.

• 

Never alter the unit in any manner. Safety in hazardous locations may be endangered if additional openings or other 

alterations are made in units specifically designed for use in these locations.

• 

Do not connect this station to the system when power is on.

• 

After installation, ensure that all threaded joints are properly tightened.

• 

Keep the unit tightly closed when in operation.

• 

After installation, test the station and the system to ensure that it is operating properly.

• 

After testing is complete, provide a copy of this instruction sheet to all personnel.

• 

Establish a procedure to routinely check the station and system for proper activation and operation.

Failure to follow all safety precautions and instructions may result in property damage, serious injury, or death.

Certifications

ATEX and IECEx Certification Information:

Certificate Nos.

ATEX Cert No.: DEMKO 19 ATEX 1939X 

IECEx Cert No.: IECEx UL 19.0074X

ATEX coding

 II 2 G D

Protection

II 2 G Ex db eb mb IIC T4 Gb (Tamb= -40°C to +70°C) 

CP-BG models: II 2 D Ex tb IIIC T100°C Db IP66 

CP-PB models: II 2 D Ex tb IIIC T100°C Db IP65

EN60079-0, EN60079-1, EN60079-7, EN60079-18, EN60079-31, IEC60079-0, IEC 60079-1, IEC60079-7, IEC60079-18, 

IEC60079-31

Refer to Certificates for specific standard versions.

Specific Conditions of Use

1. 

The equipment has an optional protective non-metallic cover that may provide a potential electrostatic charging 

hazard.

Manual Call Point

Pushbutton and Break Glass Stations for Use in 

Hazardous Locations

25500424 Rev A2 0522

Summary of Contents for CP-BG Series

























Reviews: