Federal Signal Corporation CP-BG Series User Manual Download

Page: 12 / 24

Federal Signal

signaling.fedsig.com

Failure to conduct a compatibility check per the guidelines listed below may lead to property damage, serious injury,

or death.

Models with no LED

•

Standby Mode Impedance: Equal to the EOL Resistor value (no EOL Resistor equals infinite Ω).

•

Alarm Mode Impedance: Equal to the Series Resistor value (no Series Resistor equals 0Ω).

Models with Factory Provided LED

•

Standby Mode Impedance: Equal to the EOL Resistor value (no EOL Resistor equals infinite Ω).

•

Alarm Mode Impedance: Variable. Based on EOL selected and models rated voltage. Refer to Table 1 below. Models

with a factory provided LED will contain the following installed LED series resistors: 6 V model: 470 Ω, 12 V model:

1 KΩ, 24 V: 1.8 KΩ, and 48 V model: 3.3 KΩ. Table 1 takes this additional impedance into account.

Table 2 Alarm Mode

ALARM MODE NOMINAL IMPEDANCE FOR A CALLPOINT

WITH LED MODULE

6 V

12 V

24 V

48 V

L RESI

470

235.00

319.73

1000

319.73

500.00

642.86

2200

387.27

687.50

990.00

1320.00

3300

411.41

767.44

1164.71

1650.00

4700

427.27

824.56

1301.54

1938.75

5000

429.62

833.33

1323.53

1987.95

5600

433.61

848.48

1362.16

2076.40

10000

448.90

909.09

1525.42

2481.20

12000

452.29

923.08

1565.22

2588.24

15000

455.72

937.50

1607.14

2704.92

22000

460.17

956.52

1663.87

2869.57

33000

463.40

970.59

1706.90

3000.00

47000

465.35

979.17

1733.61

3083.50

Electrical Specifications

Maximum Input Voltage: 6, 12, 24, or 48 Vdc when LEDs are present; if no LEDs are present, 48 Vdc maximum.

Maximum Input Current: 5 A / 1 A*

*1 A with FS-approved diode installed (See Table 2 on page 23 for the diode part number.)

Before connecting to the power, confirm that the external voltage source and internal EOL/Series resistor values are in

accordance as shown above. The resistance of the resistor modules are marked on the resistor module enclosures. If

the EOL/series resistor value chosen is outside the range above, the hazardous area safety protection of the Ex potted

module is compromised. The maximum power dissipation on the resistor is 1 W. Failure to observe this warning may

lead to property damage, serious injury, or death.

Maximum Ground Wire: 12 AWG / 2.05 mm

Summary of Contents for CP-BG Series

























Search results

Summary of Contents for CP-BG Series

Reviews:

Related manuals for CP-BG Series

Brands by name

Popular brands

Federal Signal Corporation CP-BG Series, Manual

Search results

Summary of Contents for CP-BG Series

Reviews:

Related manuals for CP-BG Series

Brands by name

Popular brands