Federal Signal Corporation Allegiant ALGT61 Installation Maintenance And Service Manual Download Page 26

Page: 26 / 28

Allegiant

Tow Discrete Light Bar

Federal Signal

www.fedsig.com

Getting Technical Support and Service

For technical support and service, please contact:
Service Department

Federal Signal Corporation

Phone: 1-800-433-9132

Email: [email protected]

www.fedsig.com

Getting Repair Service

The Federal Signal factory provides technical assistance with any problems that

cannot be handled locally.
Any units returned to Federal Signal for service, inspection, or repair must be

accompanied by a Return Material Authorization (RMA). Obtain an RMA from a local

Distributor or Manufacturer’s Representative.
Provide a brief explanation of the service requested or the nature of the malfunction.
Address all communications and shipments to the following:
Federal Signal Corporation

Service Department

2645 Federal Signal Drive

University Park, IL 60484-3167

Summary of Contents for Allegiant ALGT61




























Search results

Summary of Contents for Allegiant ALGT61

Reviews:

Related manuals for Allegiant ALGT61

Brands by name

Popular brands

Federal Signal Corporation Allegiant ALGT61, Installation Maintenance And Service Manual

Search results

Summary of Contents for Allegiant ALGT61

Reviews:

Related manuals for Allegiant ALGT61

Brands by name

Popular brands