manualshive.com logo in svg

Fayat DYNAPAC F1800C, Operation & Maintenance Manual


Share
Download
background image

C 10.18 6

3.3

Lashing equipment

Use the load securing equipment, lashing straps and chains belonging to the vehicle.
Additional shackles, eyebolts, edge guards and non-slip mats may be needed de-
pending on the type of load securing equipment.

m

Always comply with the stated values for permitted lashing force and load rating!

m

Always tighten the lashing chains and straps hand-tight (100-150 daN).

m

Lashing equipment must be checked by the user for any signs of damage before use.
On detecting any signs of damage that affect safety, the lashing equipment must be
withdrawn from further use. 

-

Lashing chain
permissible lashing force LC 4,000 daN

-

Lashing straps
permissible lashing force LC 4,000 daN

-

Shackles
Load rating 4,000 daN

-

Edge guards for lashing straps

-

Non-slip mats

Summary of Contents for DYNAPAC F1800C











































































































































































































































































































































Reviews:

No comments

Related manuals for DYNAPAC F1800C

Brands by name

Popular brands

Load more brands