manualshive.com logo in svg

Fayat DYNAPAC F1800C, Operation & Maintenance Manual


Share
Download
background image

F 60.18 14

m

Always comply with the following instructions when installing and removing hydrau-
lic hoses:

- Always only use original Dynapac hydraulic hoses!
- Always observe high standards of cleanliness!
- Hydraulic hoses must always be fitted to ensure that in all operating statuses,

- there is no tensile load apart from dead weight.
- there is no compressive load for short lengths.
- any external mechanical impact on the hydraulic hoses is avoided.
- appropriate positioning and fastening of the hoses prevents them from chafing on

components or on each other. 
components with sharp edges must be covered when installing hydraulic hoses.

- bending radii are not smaller than the permitted values.

- When hydraulic hoses are connected to moving parts, the length of the hose must

be dimensioned to ensure that the bending radii are not smaller than the permitted
smallest values right across the full range of movement and/or that the hydraulic
hose is not also exposed to tension.

- Fasten the hydraulic hoses to the provided fastening points. the hoses must not be

hindered in their natural movement and change in length.

- Painting the hydraulic hoses is forbidden! 

Summary of Contents for DYNAPAC F1800C











































































































































































































































































































































Reviews:

No comments

Related manuals for DYNAPAC F1800C

Brands by name

Popular brands

Load more brands