manualshive.com logo in svg

Faulhaber MCDC2805 series, Instruction Manual, Page: 52 / 60

Share
Download
Faulhaber MCDC2805 series Instruction Manual Download Page 52

52

Appendix

Example Configurations and Programs

The following examples are programmed from
the basis of the factory settings.

Velocity Control: Command value received as a
PWM signal at the analog input. 

Goals:

■

Velocity control with a PWM signal at the
analog input.

■

Limit acceleration to 500 Rev/s

2

■

Set scaling so that a maximum speed of 
5000 rpm is possible.

■

Set the parameters, proportional term to 
30 and the integral term to 15

ASCII Command form:
SOR2
AC500
SP5000
POR30
I15
EEPSAV 

➔

Saves configuration in EEPROM

Velocity Control: Command value received at
the RS-232 port

Goals:

■

Velocity control at the RS-232 port.

■

Two active limiter switches (high level active)
cannot be passed.

■

Set peak current to 3 A

ASCII Command form:
SOR0
REFIN

➔ 

Defines the fault pin as a limiter
switch input

HP3

➔ 

Both limiter switches are set to high
level

HB3

➔ 

Both limiter switches are set to Hard
Blocking

HD1

➔ 

Blocks right direction of rotation at
the analog limiter switch and left
direction of rotation at the Fault Pin
limiter switch.

LPC3000

LCC1000

V0

➔ 

Switches to velocity control mode and
stops.

EEPSAV

➔ 

Saves configuration to the EEPROM

Summary of Contents for MCDC2805 series





























































Reviews:

No comments