background image

4th edition, 26-08-2020

7000.05058, 4th edition, 26-08-2020

7000.05058

Installation

17

4.1.2

Mounting on the front flange

Fig. 6:

V3 installation schematic diagram

NOTICE!

If the Motion Control System is installed with the shaft end facing upwards, liquids can 
accumulate on the upward-facing surface and damage the device.

With V3 installation (see Fig. 6), make sure that no liquids can penetrate the bearings.

Optional: Use a Motion Control System with an additional shaft seal. Fitting a shaft seal 
may reduce the motor performance (see chap. 4.1, p. 16)

Secure the Motion Control System (1) with screws (2) using the tapped bore holes on 
the cover plate as shown in Fig. 7.

The maximum tightening torque of the screws is 130 Ncm.

The maximum screw-in depth is 4 mm.

Fig. 7:

Mounting on the front flange

Using option 5657 and when the base drive is directly flange-mounted or in combina-
tion with attachments (e.g. gearboxes), an additional seal (O-ring), to enhance the pro-
tection class of the complete system, may be installed between the drive and the 
attachment (see chap. 5.2, p. 39).

1

2

Summary of Contents for 3242 BX4 Series












































Reviews: