background image

Heat recovery unit with cooling circuit - 

RCF

 -

0208-6180549-rev. 02

8

GB

Controls manual 

Heating LED 
 

• 

ON if the unit is in  

 

Heating mode. 

 

Cooling LED 
 

• 

ON if the controller  

 

is in Cooling mode

If  neither  the  HEAT  LED  or  the 
COOL  LED  are  lit,  the  controller  is  in 
STANDBY mode.

On board control panel

The  control  panel  on  borad  of  the  unit 
performs the same functions and displays 
the  same  parameters  of  the  remote 
panel.
The  setting  procedure  are  the  same 
described for the remote panel. 
The “Upwards arrow” button operates also 
as “Mode” button, while the “Downwards 
arrow” button operates also as “Set” but-
ton.

Parameter programming – Menu levels

The  setting  parameters  of  the  control 
device may be modified through the con-
trol panel keyborad. The various parame-
ters  are  organized  in  groups  accessible 
when  pressing  the “mode”  and “on-off” 
buttons  at  the  same  time.  Each  menu 
level  is  identified  by  a  mnemonic  code 
which  appears  on  the  display.  For  more 
info please refer to the following page.

Buttons

 

 

Selects the operating mode:
If  the  Heating  mode  is  enabled,  each  time 
the button is pressed the following sequence 
occurs:
stand-by ->� cooling ->�heating -> stand-by
If the Heating mode is not enabled: 
stand-by -> cooling -> stand-by
 

 

 

Resets alarms and modifies the set point.
Press  once  to  reset  all  inactive  alarms  that 
can be reset manually.
If you hold the button down for 2 seconds, 
the  unit  displays  the  set  point  of  the  set 
mode. 

 

       

If  you  press  both  buttons  at  the  same  time 
and then release them within 2 seconds, you 
go down one level in the display menu.
If  you  press  both  buttons  for  more  than  2 
seconds, you move one level up. 
If the last level of a menu is displayed, press 
the button and release it within two seconds 
to go up one level.

In  menù  operating  mode  it  shows  the  pre-
vious  label  or  increases  the  shown  value 
(depending on the context). 

In  menù  operating  mode  it  shows  the  fol-
lowing  label  or  decreases  the  shown  value 
(depending on the context)

MODE

SET

Display

In Normal mode, the unit displays:
•  the  control  temperature,  in  tenths  of 
degrees  Celsius  with  a  decimal  point  or 
in Fahrenheit with no decimal point.
•  the  alarm  code,  if  at  least  one  is  acti-
ve.  If  several  alarms  are  active,  the  unit 
displays  the  first  alarm  listed  in  the 
Alarm Table. 
•  If  temperature  control  is  not  based 
on  the  analogue  inputs  and  is  linked  to 
the  status  of  a  digital  input  (AI1  or  AI2 
configured  as  digital  inputs),  the “On” 
or “Off”  label  will  be  displayed,  depen-
ding  on  whether  temperature  control  is 
active or not. 
•  In  Menu  mode,  displaying  varies 
according  it  the  position.    Special  labels 
and codes are used to help users identi-
fy the function that has been set.
Decimal point: when displaying the ope-
rating  hours,  it  indicates  that  the  value 
must be multiplied x 100.

In  normal  operation,  the  display  shows  
the temperature given by the NTC probe  
on the exhaust flow (room temperature).
To  display  the  setting  keep  the  button 
“set” pushed for nearly 3 seconds.
 

Leds

LED 1 compressor 1
 

• 

ON if compressor 1  

 

is active

 

• 

OFF if compressor 1  

 

is inactive

•    BLINK if safety timing is in progress

Defrost LED
 

• 

ON if defrosting is  

 

active

 

• 

OFF if defrosting     

 

is disabled or has been  

 

completed

•      BLINK  if  timing  is  in  progress  (defro-
sting time)

Electric heater LED
 

• 

ON if the internal    

 

anti-freeze electric heater  

 

are on

•  OFF  if  the  internal  anti-freeze  electric 
heater are off

MODE

SET

Summary of Contents for RCF Series




























Reviews: