background image

 

 

 

1

 

Part #30161 

Revised 8/14/07 

FAST™ 

3400 Democrat Rd. 

Memphis, TN  38118 

Phone:  (901) 260-3278 Fax:  (901) 375-3408 

www.fuelairspark.com 

 
 

                                                                                                      
                  

 

 

#307500 and #307501 FAST™ Fuel System Kits 

 

Thank you for choosing FAST™ products; we are proud to be your manufacturer of choice. Please 
read this instruction sheet carefully before beginning the installation.  

 
Kit Contents

 
 
 

 

 
 
 
 
 
 
 

 
 
 
 
Caution: Installation of this product requires detailed knowledge of automotive systems and 
repair procedures. We recommend that this installation be carried out by a qualified automotive 
technician. Installation of this product requires handling of gasoline. Ensure you are working in 
a well ventilated area with an approved fire extinguisher nearby. Extinguish all open flames, 
prohibit smoking and eliminate all sources of ignition in the area of the vehicle before proceeding 
with the installation. When installing this product, wear eye goggles and other safety apparel as 
needed to protect yourself from debris and sprayed gasoline.  
 
Warning: The fuel system is under pressure. Do not open the fuel system until the pressure has 
been relieved. Refer to the appropriate vehicle service manual for the procedure and precautions 
for relieving the fuel system pressure. FAST™ fuel system components are not legal for sale or 
use on emission controlled motor vehicles. The included FAST™ fuel pump is not compatible 
with alcohol based fuels or fuel additives! 
 

This kit assumes you have a sumped fuel tank or fuel cell with accommodations for an AN-10 supply 
line and an AN-06 return line. Fuel tank pickups will not work properly with FAST™ fuel systems and 
will be detrimental to your fuel systems life. If your fuel tank is not sumped, we recommend having 
your fuel tank sumped by a qualified professional. No fuel rails are provided with this kit, your fuel 
rails must have accommodations to accept AN-08 hose ends in order to install this kit properly. 

 
 

INSTRUCTIONS 

1 ea  

fuel pump wiring kit 

1 ea  

3ft length of 10 ga. Black wire 

1 ea  

25ft length of 10 ga. Red wire 

1 ea  

30 amp circuit breaker 

1 ea  

30 amp automotive relay 

2 ea  

blue female blade connector 

2 ea  

yellow female blade connector 

5 ea  

yellow #10 stud ring connector 

1 ea  

yellow 3/8” stud ring connector 

6 ea  

tie-wraps 

1 ea  

AN-06 cutoff union 

3 ea  

AN-10 cutoff union 

3 ea  

AN-10 cutoff to AN-08 union

 

1 ea  

Pump 

1 ea  

Filter 100 Micron SS 

1 ea  

Filter 10 Micron Paper 

1 ea  

Fuel Pressure Regulator 

1 ea  

Y-block Assembly 

2 ea  

AN-08 cutoff union 

2 ea  

AN-08 o-ring 

1 ea  

AN-10 cutoff to AN-08 union 

1 ea  

AN-10 o-ring 

12 ea  

tie-wraps 

1 ea  

AN-06 o-ring 

8 ea  

AN-10 o-ring 

 

Summary of Contents for 307500













Reviews: