background image

 

 

 

12

 

Part #30161 

Revised 8/14/07 

FAST™ 

3400 Democrat Rd. 

Memphis, TN  38118 

Phone:  (901) 260-3278 Fax:  (901) 375-3408 

www.fuelairspark.com 

7.

 

Once the desired fuel pressure is achieved, tighten the regulator adjustment jam nut & attach 
vacuum line. 

 

8.

 

Test drive the car to ensure proper operation and re-check the fuel system for leaks. 

If any 

leaks are found, immediately discontinue use of the vehicle and repair the leak(s)! 

 
 
 
 
 
 
 

Limited Warranty 

 
 

FAST, Inc. warrants that all of its products are free from defects in material and workmanship for a 
period of 1 year from the date of purchase. This limited warranty shall cover the original purchaser. 
 
FAST, Inc.’s obligation under this warranty is limited to the repair or replacement of its product. To 
make a warranty claim, the part must be returned within 1 year of purchase to the address listed below, 
freight prepaid. Items covered under warranty will be returned to you freight collect. 
 
It is the responsibility of the installer to ensure that all of the components are correct before 
installation. We assume no liability for any errors made in tolerances, component selection, or 
installation. 

 
There is absolutely no warranty on the following: 

 

Any parts used in racing applications. 

 

Any product that has been physically altered, improperly installed or maintained. 

 

Any product used in improper applications, abused, or not used in conjunction with the 
proper parts. 

 
There are no implied warranties of merchantability or fitness for a particular purpose.

 There are 

no warranties, which extend beyond the description of the face hereof. FAST, Inc. will not be 
responsible for incidental and consequential damages, property damage or personal injury damages to 
the extent permitted by law. Where required by law, implied warranties or merchantability and fitness 
are limited to a term of 1 year from the date of original purchase. This warranty gives you specific 
legal rights and you may also have other legal rights, which vary from state to state. 

 

 
 
 

 

Summary of Contents for 307500













Reviews: