Fass TITANIUM SIGNATURE Series Installation Manual Download

Page: 38 / 41

www.fassride.com

(866) 769.3747

STEP

REVIEW INSTALLATION

*****The factory suction line can be capped off or removed from the truck. The openings on the

filter and tank will need to be capped off to keep debris from getting into lines or canister.*****

To assist with priming your FASS pump crack the

XWS-3002

. Put power to the FASS pump to

activate the pump. When the tone of the pump changes you can tighten up the fuel filter. If you

need a video of the priming process go to www.FASSride.com.

Note: The Red Plastic Plugs located in the “H” ports can stay in place fuel will not flow through

these ports. Coolant can be plumbed into these ports to heat the fuel in the

inter months.

Summary of Contents for TITANIUM SIGNATURE Series










































Search results

Summary of Contents for TITANIUM SIGNATURE Series

Reviews:

Related manuals for TITANIUM SIGNATURE Series

Brands by name

Popular brands

Fass TITANIUM SIGNATURE Series, Installation Manual

Search results

Summary of Contents for TITANIUM SIGNATURE Series

Reviews:

Related manuals for TITANIUM SIGNATURE Series

Brands by name

Popular brands