FarmTronics ChickenMaster PRO Page 35 User Manual Download

Page: 35 / 43

Page

ChickenMaster PRO User Guide

Firmware 01.14B

Revision 1.0 23/05/2022

The

Den

, 100 Fox Drive, Dandenong South. Victoria. 3175.

www.farmtronics.com.au

Phone: 0411 479 411

Main Settings Menu

Internal Lighting

AUTOMATIC MODE MODALITY

Default value = SUNRISE/SUNSET

AUTOMATIC MODE ON/OFF SETTINGS

(When the TIME CLOCK Option is selected)

Main Settings Menu

Internal Lighting

Automatic Mode On/Off Settings

Main Settings Menu

Internal Lighting

Automatic Mode On/Off Settings

MORNING ON TIME

Default value = 05:00

Main Settings Menu

Internal Lighting

Automatic Mode On/Off Settings

MORNING OFF TIME

Default value = 07:30

Sets the ON time for the Internal Lighting in the Morning

Sets the OFF time for the Internal Lighting in the Morning

Sets the ON time for the Internal Lighting in the Evening

Sets the OFF time for the Internal Lighting in the Evening

Summary of Contents for ChickenMaster PRO












































Search results

Summary of Contents for ChickenMaster PRO

Reviews:

Related manuals for ChickenMaster PRO

Brands by name

Popular brands

FarmTronics ChickenMaster PRO, User Manual

Search results

Summary of Contents for ChickenMaster PRO

Reviews:

Related manuals for ChickenMaster PRO

Brands by name

Popular brands