background image

33

GROWSPAN

 GOTHIC PRO GREENHOUSES AND SYSTEMS

Revision date: 06.06.18    113836_37_38_39DD

INSTALL OVERLAP BRACING AND U-CHANNEL

View from 

outside.

Upper Panel

Lower Panel

Install 8' aluminum 

profile here along edge 

of upper panel.

Upper 

Panel

Aluminum profile attached 

to bottom of upper panel 

(outside of frame). 

Lower Panel

Foil tape at top of lower panel. 

Complete this procedure to finish panel installation:
1.  Install 8' sections of aluminum profile (104213) along 

lower edge of all upper panels on both sides. Trim last 

section to length as needed. 

NOTE:

 Install long side of 

profile on top of panel.  

 

Do not use Tek screws or 

washers when installing 

aluminum U-channel at this 

time. 

104213 U-Channel

Long Side 

of Profile

2.  Move inside the frame and measure between rafters at 

point where upper and lower panels overlap.

3.  Cut a piece of 104779 (1.5" x 1.5") square tubing to fit 

between rafters. (All tubes should be same length.) 

NOTE:

 Diagram (above) shows where to measure to 

determine length of 1.5" x 1.5" tube. Diagram shows 

installed panels as seen standing inside greenhouse.

4.  From inside the frame, align square tube as shown 

over lower end of upper panel (dashed line). Hold tube 

in place tight against panel. 

1.5" x1.5" Tube

(104779)

View from inside the shelter.

Foil tape at top of lower panel. 

ATTENTION:

 Align and install tube as shown to secure 

upper and lower panels together at overlap seam. 

View shows underside of panels as seen from inside 

greenhouse.

IMPORTANT

Under no circumstances should a 

support structure allow force or weight to be applied to 

polycarbonate panels! Supports must span from rafter 

to rafter when used. Consult a contractor if needed for 

additional information. Take additional steps to protect 

polycarbonate panel surface. 

Use of a lift is strongly 

recommended.

If bracing and U-channel trim were installed during 

panel installation, skip this section and continue with the 

installation of baseboards.

Foil Tape 

(top of lower 

panel inside)

Lower 

Panel

1.5" x 1.5" (104779) 

Backer Tube 

(inside greenhouse)

U-Channel (bottom of 

upper panel – outside)

Upper 

Panel

Install 104213 

U-channel here.

Dashed line shows 

top of all lower panels 

(inside greenhouse).

Summary of Contents for Growers supply GrowSpan Gothic Pro 113836DD






























































Reviews: