background image

9

COMMERCIAL CANOPIES

Revision date: 06.22.10

SQUARE THE ASSEMBLED FRAME

Gather the parts
•  Measuring tape and assistants 

Complete these steps:
1. 

With the frame in position, perform a final square of the

 

frame by measuring diagonally (corner-to-corner) as 

shown below at the bottom of the legs. Verify that the 

two measurements are equal and adjust if needed.

2.  Adjust width to 14' on-center. Measure width from 

center of rafter leg to center of other rafter leg of the 

same rafter assembly. Adjust if needed. Repeat for all 

rafter assemblies.

FRAME TOP VIEW

3.  Examine the frame and remove any sharp edges from  

the frame or reposition screws (if equipped) so they do 

not come in contact with the roof cover.

4.  After the frame is squared, read or reread the MUST  

READ document and anchor the shelter.

ANCHOR THE SHELTER

At this point, anchor the shelter. Consult the MUST READ 

document for anchoring information and suggestions. 

Please call customer service at 1-800-245-9881 for 

additional anchoring information.

 CAUTION

: The anchor assembly is an integral part of

 

the shelter construction. Improper anchoring may 

cause shelter instability and failure of the structure 

to perform as designed. Failing to anchor the shelter 

properly will void the manufacturer’s warranty and may 

cause serious injury and damage.

FRAME ASSEMBLY (CONTINUED)

4.  While lifting one side of the assembled roof structure, 

insert a 77″ pipe into the 3-way and 4-way couplers 

then tighten eye bolts. Refer to the illustration below.

5.  Repeat the step for the other side of the frame.
6.  Verify that all eye bolts are tight and square the frame. 

14'

On-center width is 14'.

Summary of Contents for 1420CC




















Reviews: