background image

COMMERCIAL CANOPIES

12

Revision date: 06.22.10

13. On the side of the shelter where the D-ring straps are 

located, lift the main cover skirt (if present) and cut a 

slit through the main cover pocket in line with the rafter 

or rafters.

14. Thread the D-ring strap through the slit in the cover 

pocket, wrap it around the cover conduit, and attach 

the strap assembly to the rafter. 

NOTE:

 Verify that the cover is centered side-to-side 

before attaching the D-ring straps. If optional side 

panels were attached, install the Tek screw through the 

panel.

15. Repeat the steps for the remaining D-ring straps. 

 

NOTE:

 D-ring straps are attached to one side of the 

shelter. Ratchets are attached directly across from the 

D-ring straps on the 

same rafter assembly

.

16. Move to the other side of the shelter and attach the 

ratchets to the rafters. Use the cover conduit and strap 

as guides to attach the ratchets to the rafters at the 

proper height. Fasten ratchets to the outside of these 

rafters using Tek screws.

17. As previously described, make a slit in the cover 

conduit pocket and insert a 3' section of plain strap 

through the slit and around the cover conduit. 

INSTALL COVER (CONTINUED)

18. Thread the strap ends into a ratchet and slightly 

tighten. 

 

NOTE:

 It may be necessary to remove excess strap if it 

binds up in the ratchet.

19. Repeat the steps for the remaining ratchet or ratchets.
20. Using additional help (if needed) tighten the main cover 

beginning with the ratchet or ratchets along the side of 

the shelter frame.

21. After the side ratchets are tightened, return to the end 

ratchets and tighten. 

 

NOTE:

 Loosen the ratchets if needed to remove 

excess strap and tighten. If the main cover is not 

centered as desired, the D-rings straps can be 

repositioned (higher or lower) as needed and the main 

cover retightened.

22. Fold the skirt of main cover down and over the ratchets 

and D-ring straps to complete the installation of the 

main cover.  

 

NOTE:

 Depending on the shelter, some main covers 

may not include a cover skirt.

Summary of Contents for 1420CC




















Reviews: