FarmTek 106310PC Manual Download

Page: 47 / 51

GROWSPAN

™

GOTHIC PRO GREENHOUSES AND SYSTEMS

Revision date: 05.29.19

H-CHANNEL

INST

ALLA

TION INSTRUCTIONS

The new H-channel design requires installation of the flat side facing out with channel side toward the building. Some diagrams

and photos in this document show installation of

original

H-channel with channel side facing out. Design of new H-channel

does not allow

channel-side out installation.

Use the diagrams on this page to install H-channel with flat side facing out.

ATTENTION:

Use only 1-1/2"

Tek screws to

attach H-channel to building frame.

Do not use

shorter screws. They will not hold. Do not use washers on T

ek screws when installing

H-channel.

ATTENTION:

Install all twin-wall polycarbonate panels with UV

-protected side toward the sun.

-protected side toward sun.

Install 1-1/2"

Tek screws through

H-channel into building frame.

H-Channel

Center Groove

Flat side toward the sun.

Flat Side

Channel

Summary of Contents for 106310PC




















































Search results

Summary of Contents for 106310PC

Reviews:

Related manuals for 106310PC

Brands by name

Popular brands

FarmTek 106310PC, Manual

Search results

Summary of Contents for 106310PC

Reviews:

Related manuals for 106310PC

Brands by name

Popular brands