manualshive.com logo in svg

Farmi Forest Corporation 61, Operation And Maintenance Manual, Page: 26 / 50

Share
Download
Farmi Forest Corporation 61 Operation And Maintenance Manual Download Page 26

FARMI 61

26

TROUBLE SHOOTING

CONDITION

POSSIBLE CAUSE

REMEDY

Hard to pull the cable out

Drum brake is too tight.

Loosen the drum brake. See 

instructions from item ”Adjusting 

the drum brake”.

The clutch is too tight

Loosen the clutch

Cable gets tangled on the drum.

Cable too loose on the drum. The 

cable is pressed between loose 

loops.

Disengage the brake and drive 

the cable out from the drum by 

means of the tractor. Reel the 

cable tightly back in with the help 

of the load.

Cable develops kinks.

Cable brake too loose

Tighten the drum brake.Tighten 

cable on the drum by pulling out 

the cable and by winching with a 

heavy load.

Roller chain comes off.

Roller chain too loose, some part is 

broken or the aligning is incorrect.

Check the aligment of the chain. 

Check possible damages.  

Adjust the roller chain, change if 

necessary. See chapter ”Adjusting 

the roller chain”.

Rattling sound

Roller chain too tight, some part is 

broken or the aligning is incorrect.

Check the aligment of the chain. 

Check possible damages.  

Adjust the roller chain, change if 

necessary. See chapter ”Adjusting 

the roller chain”.

Insufficient pull on the cable

Normal wear of the clutch.  

Minimum thickness of the clutch 

plates is 7 mm.

See chapter ”Clutch adjustment”

Oil or grease in the clutch

Disassemble and clean the parts.

Clutch too loosely adjusted

Adjustment of the clutch. See 

chapter ”Clutch adjustment”

Tractor slides backwards when

winching

Parking brakes are not on. 

Dozer blade does not anchor the 

unit firmly to the ground.

Lock on the parking brakes. 

Lower the winch all way to the 

ground.

Summary of Contents for 61



















































Reviews:

No comments