background image

FARMI 61

23

35 kg

C

Fig. 16. Clutch adjustment

CLUTCH ADJUSTMENT

The clutch is easy to operate. It does not exert to keep 

the clutch pulled because the lever is pulled over the 

highest transfer strength 35 kg outside up to the im-

pact. In impact proximity the transfer strength is only 

10-15 kg.

It is important that the clutch is 

adjusted correctly and the im-

pact is not changed, otherwise 

exists danger that the clutch 

goes beyond the so-called dead 

point and cannot the drive any 

longer be switched off.

CHECK

•  Measure the strength of the control rope e.g. with 

the help of a spring scale or a weight.

•  If the maximum force is below the desired level, 

tighten the clutch. If the force exceeds the desired 

level, loosen the clutch.

ADJUSTING

1.  Loosen the axle nut’s (C) lock screw.

2.  Turn the nut (C) (horizontal width: 50 mm) slightly  

in the required direction – clockwise to tighten 

the clutch and counter-clockwise to loosen it.

3.  Use the scales to pull the clutch lever (A) close to  

the limiter (B).

4.  After reaching the desired maximum force, lock  

the nut (C).

If you overtighten the nut (C), the 

string force will increase but the 

winch will not pull well.

If the nut is too loose, the string 

force will be light but the clutch 

could slip.

WARNING!

!

CAUTION!

!

Summary of Contents for 61



















































Reviews: