Farmet VIDIUM P 350 Operating Manual Download | Manualshive

Page: 16 / 24

background image

Manual

VIDIUM P 350 | P 450

16

│

24

Adjusting the Chassis to the Work Coverage Setting–> only in P 450!

1.

Loosen bolts S

2.

Remove fixing bolt F1

3.

Tilt chassis 1 so that the required openings are
above one another (according to the diagram)

4.

Install fixing bolt F1back

5.

Remove fixing bolt F2

6.

Tilt the end of frame 2 so that the required
openings are above one another

7.

Install fixing bolt F2 back

8.

Tighten bolts S, F1, F2

5.3.2

Gross Adjustment of the Plough to the Tractor Width

Based on the different interior spacing of the rear tractor wheels A and the set work coverage S, the plough
is first adjusted grossly using the support X guidance.

Additionally, the interior spacing of the wheels of the chassis to the depth of ploughing has to be adjusted.
The interior distance is in the following table:

«
...
14
15
16
17
18
...
»

Summary of Contents for VIDIUM P 350

























Reviews:

No comments

Related manuals for VIDIUM P 350

Brand: ParaBody Pages: 4

Brand: IBS Scherer Pages: 64

DISHSTAR ADA-SEER

Brand: Jackson Pages: 2

Brand: JBL Pages: 38

Brand: JBSYSTEMS Light Pages: 32

Brand: JBM Pages: 12

Brand: OAKWORKS Pages: 2

Brand: Oakton Pages: 2

Brand: Oakton Pages: 2

Brand: O2matic Pages: 4

Brand: Waterpik Pages: 2

Brand: WaterUps Pages: 2

Brand: A&D Pages: 29

Brand: YASKAWA Pages: 81

Brand: YASKAWA Pages: 52

Brand: Zennio Pages: 3

Brand: Dantel Pages: 22

Heart Guardian AED

Brand: Radian Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands