manualshive.com logo in svg

Farmet K400NS, Operating Manual

Share
Download
Farmet K400NS Operating Manual Download Page 36

 

 

 

 

 

 

Manual

 

KOMPAKTOMAT K400NS  |  K500NS |  K600NS

 

36 

│

 42 

8.

 

INSTALLING TRACK CULTIVATORS BEHIND THE MACHINE 

 

As mentioned above, the track cultivators are not standardly included in the equipment of the mounted 
Kompaktomat machines.  

 

The  installation  of  the  cultivators  moves  the  centre  of  gravity  of  the  machine  further  away  from  the 
tractor.  

 

Pay  attention  to  observing  the  valid  regulations  regarding  the  permitted  load  of  the  front  axle  of  the 
tractor. 

8.1.

 

TRACK CULTIVATORS FOR K400NS 

 

Observe generally valid safety regulations when installing the track cultivators.  

 

The track cultivators are installed on the frame for the cultivators between the tractor and the machine.  

 

The frame with the cultivators is attached to the frame of the K400NS machine. The set is aggregated to 
the rear hitch of the tractor similarly as K400NS without cultivators. 

 

The setting of the track cultivators is described in Chapter 6.1. 

 

 

Summary of Contents for K400NS











































Reviews:

No comments

Brands by name

Popular brands

Load more brands