- 29 -
Mi 2478
I
T
ALIANO
E
NGLISH
F
RANÇAIS
E
SP
AÑOL
P
ORTUGUÊS
D
EUTSCH
Back
Advanced
Default
Show
settings
Show
settings
System
Back
Actuations
Favourite
buttons
Favourite
buttons
Entrances
Installation
wizard
Installation
wizard
Intercommunicating
Access the main menu
With the monitor in stand-by and no other videointercom
turned ON in the system, access the menu by touching
any active point of the wheel sensor. From the menu the
user can access all programming, setup, adjustments
and activation pages of the videointercom.
Access the “Favourite buttons” menu
With the monitor in stand-by and no other videointercom
turned ON in the system, to access the favourite buttons
menu and the specific functions associated to every key
during programming (favourite buttons).
The next image shows the display with factory settings.
If on middle bottom screen are displayed 2 or more
boxes it means that the functions are present in several
pages. Use the keys
or rotate the wheel sensor
to move from one page to another.
3
PROGRAMMING
To ensure correct operation of the videointercom, the latter must
be programmed by the installer; incorrect programming may
compromise the operation of the whole system.
The main parameters to be set are the following:
User address
(mandatory); this address identifies the
videointercom device within the installation. Enter a number from
001 to 200 taking into consideration the following:
- the number of the apartment should not be equal to that of an
another apartment; if there are several internal stations connected
in parallel in the same apartment, they should have the same user
address but different room number (see the next section);
- it should match the address stored in the external push-button
panel and the door keeper exchanger, if any;
- it should be stored in the calling key and the contacts of another
device, if intercommunication between the two users is required.
Room number
(mandatory in case of multiple devices in the
same apartment); identification address of a device inside the
same apartment
(addresses from 000 to 009). The room number
establishes a hierarchy in the internal devices since the device
with room address 0 (zero) will be the main device and all the
other devices will be the secondary ones. The different room
number enables making/receiving calls between devices installed
within the same apartment selectively. The external calls or calls
from another apartment will make all devices ringing, the first
device that answers the call will activate the conversation and
switch OFF the ringer of the other devices. When you receive a
call from an external door station equipped with camera, all the
devices will ring, but only the main device
(room address 0 - zero)
will display the camera image. The entrance can be displayed
from any of the other videointercom installed in the same apartment
by pressing the key “
”; this key disables all buzzers, turns ON
the relative videointercom, while turning OFF the main
videointercom screen.
Intercommunication devices; names and addresses of
other devices that you intend to communicate with such as:
- users of other apartments; it allows to call them selectively
(addresses from 001 to 200);
- videointercoms in the same apartment; it allows to
intercommunicate with the equipment of other rooms in the same
apartment
(room number from 000 to 009);
- door keeper exchangers (
addresses from 201 to 210).
Entrances; names and addresses of external door stations
(not necessary in the case of a single door station) to enable the
videointercom to monitor these entrances separately and oper-
ate the lock, if needed (
addresses from 231 to 250).
Actuations; names and addresses of actuators for additional
services (additional locks, stair lights, etc.) that can be activated
directly from the videointercom (
addresses from 211 to 220).
Favourite buttons; when the monitor is in stand-by, the 6 side
keys can be used to directly activate additional services that are
used more frequently (automatic gate, stair lights,
intercommunicating calls, calls to door keeper, etc.).
Warning: the addresses stored in the videointercom must
be the same of those programmed in the devices to
enable.
How to display next/previous functions of a page
Gate
Silent
Empty
Empty
Empty
Empty
