Faraone LEVAH 65 MOVE PICKING Use And Maintenance Instructions Download Page 8

Page: 8 / 80

USE AND MAINTENANCE MANUAL - SECTION 1

STOCK PICKER ELEVAH 65-80 MOVE PICKING – Rev. 09_2019

Page 1-2

PRELIMINARY PROCEDURES

Operator training and know-how

Carefully read the manual before using the machine.

Use the machine only after complete training by authorised personnel.

The use of the machine is allowed exclusively to authorised and qualified
personnel.

Read carefully and follow all the WARNING statements and the

operational instructions reported on the machine and in the manual.

Use the machine for the applications falling within those envisioned by

Faraone Industrie Spa.

All operational personnel must familiarise with the emergency operations
and controls of the machine, as specified in the manual.

Carefully read and comply with all company, local and government

Standards in force, relating to machine operation.

Inspection of the work place

Before using the machine, the operator must take the necessary

precautions to avoid any danger in the work place.

Do not activate the machine on lorries, trailers, railway wagons, boats,

scaffolding or similar, unless Faraone Industrie Spa has approved the
operation in writing.

The machine can be switched on at temperatures between -15°C and

40°C. Contact Faraone Industrie for values relating to machine operation
at temperatures not within the indicated range.

Summary of Contents for LEVAH 65 MOVE PICKING

















































































Search results

Summary of Contents for LEVAH 65 MOVE PICKING

Reviews:

Related manuals for LEVAH 65 MOVE PICKING

Brands by name

Popular brands

Faraone LEVAH 65 MOVE PICKING, Use And Maintenance Instructions

Search results

Summary of Contents for LEVAH 65 MOVE PICKING

Reviews:

Related manuals for LEVAH 65 MOVE PICKING

Brands by name

Popular brands