ENGLISH
ENGLISH
GB-43
GB-42
Positioning the Appliance
Position the appliance in the desired location. The back should rest against the wall
behind it, and the sides, along the adjacent cabinets or walls. The dishwasher is
equipped with water supply and drain hoses that can be positioned either to the right
or the left sides to facilitate proper installation.
How to Drain Excess Water From Hoses
If the sink is 1000 higher from the floor, the excess water in hoses cannot be drained
directly into the sink. It will be necessary to drain excess water from hoses into a
bowl or suitable container that is held outside and lower than the sink.
Water Outlet
Connect the water drain hose. The drain hose must be correctly fitted to avoid water
leaks.
Ensure that the water inlet hose is not kinked or squashed.
Extension Hose
If you need a drain hose extension, make sure to use a similar drain hose.
It must be no longer than 4 metres; otherwise the cleaning effect of the dishwasher
could be reduced.
Syphon Connection
Insert the drain hose into a drain pipe with a minimum diameter of 40mm, or let it
run into the sink, making sure to avoid bending or crimping it. The top of the hose
must be less than 1000mm.
The following things should be checked before starting the dishwasher.
1.
The dishwasher is level and fixed properly
2.
The inlet valve is open
3.
There is a leakage at the connections of the conducts
4.
The wires are tightly connected
5.
The power is switched on
6.
The inlet and drain hoses are knotted
7.
All packing materials and printings should be taken out from the dishwasher
Start of Dishwasher
ATTENTION:
After installation, please make sure to keep this manual.
The content of this manual is very helpful to the users.
Before Calling for Service
Review the charts on the following pages may save you from calling for service.
Problem
Possible Causes
What To Do
Technical
problems
Dishwasher
doesn't start
Fuse blown, or the circuit breaker
acted
Replace fuse or reset circuit breaker. Remove
any other appliances sharing the same circuit
with the dishwasher
Power supply is not turned on
Make sure the dishwasher is turned on and the
door is closed securely.
Make sure the power cord is properly plugged
into the wall socket.
Water pressure is low
Check that the water supply is connected
properly and the water is turned on.
Door of dishwasher not properly
closed.
Make sure to close the door properly and
latch it.
water not
pumped form
dishwasher
Kink in drain hose
Check drain hose.
Filter clogged
Check coarse the filter
(see section titled "Cleaning The Filter")
Kitchen sink clogged
Check the kitchen sink to make sure it is
draining well.
If the problem is the kitchen sink not draining,
you may need a plumber rather than a
serviceman for dishwashers
General
problems
Suds in the tub
Improper detergent
Use only the special dishwasher detergent to
avoid suds.
If this occurs, open the dishwasher and let suds
evaporate Add 1 gallon of cold water to the tub.
Close and latch the dishwasher, then select any
cycle. Dishwasher will drain out the water at
the first step. Open the door after draining is
stop and check if the suds is disappeared.
Repeat if necessary.
Spilled rinse-aid
Always wipe up rinse-aid spills immediately.
Stained tub
interior
Detergent with colourant was
used
Make sure that the detergent is the one
without colourant.
White film on
inside surface
Hard water minerals
To clean the interior, use a damp sponge with
dishwasher detergent and wear rubber gloves.
Never use any other cleaner than dishwasher
detergent for the risk of foaming or suds.
TROUBLESHOOTING TIPS
Summary of Contents for LVFI4515PI
Page 1: ...LVFI4515PI...
