Fanvil i23 User Manual Download Page 27

Page: 27 / 59

[

键入文字

]

SIP

Field Name

Explanation

Basic Settings

(Choose the SIP line to configured)

Status

Shows registration status. If the registration is successful done,it will display “has

been registered”, otherwise will display “not registered”.The wrong password will
display “403 errors” and account number failure will display “timeout”.

Server Address

SIP server IP address or URI.

Server Port

SIP server port. Default is 5060.

Authentication

User

SIP account name (Login ID).

Authentication

Password

SIP registration password.

SIP User

Phone number assigned by VoIP service provider. Equipment will not register if there

is no phone number configured.

Display Name

Set the display name. This name is shown on Caller ID.

Enable

Registration

Check to submit registration information.

Advanced SIP Settings

Proxy Server

Address

SIP proxy server IP address or URI, (This is normally the same as the SIP Registrar

Server)

Proxy Server Port

SIP Proxy server port. Normally 5060.

Proxy User

SIP Proxy server account.

Proxy Password

SIP Proxy server password.

Backup Server

Address

Backup SIP Server Address or URI (This server will be used if the primary server is

unavailable)

Backup Server
Port

Backup SIP Server Port.

Domain Realm

SIP Domain if different than the SIP Register Server.

Server Name

Name of SIP Backup server

Summary of Contents for i23




























































Search results

Summary of Contents for i23

Reviews:

Related manuals for i23

Brands by name

Popular brands

Fanvil i23, User Manual

Search results

Summary of Contents for i23

Reviews:

Related manuals for i23

Brands by name

Popular brands