manualshive.com logo in svg

Fantom Drives MGT-08SC08A, Installation Reference Manual

Share
Download
Fantom Drives MGT-08SC08A Installation Reference Manual Download Page 85

RAID Configuring

3-51

The password option allows user to set or clear the raid subsystem’s password
protection feature. Once the password has been set, the user can only monitor
and configure the raid subsystem by providing the correct password.

The password is used to protect the internal RAID subsystem from unautho-
rized entry. The controller will check the password only when entering the Main
menu from the initial screen. The RAID subsystem will automatically go back to
the initial screen when it does not receive any command in ten seconds.

To disable the password, press 

Enter

 key only in both the 

Enter New Password

and 

Re-Enter New Password 

column. Once the user confirms the operation and

clicks the 

Submit

 button. The existing password will be cleared. No password

checking will occur when entering the main menu from the starting screen.

3.9.11 Upgrade Firmware

Please reference the section 3.12 for more information.

Summary of Contents for MGT-08SC08A

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands