background image

 

17

 

Cleaning or Winterizing 

 

Every three to six months, depending upon the water condition, you may need to renew your water.   

 

 

     CAUTION: READ THIS BEFORE DRAINING YOUR HOT TUB 

To prevent damage to the hot tub’s components, turn off power to the spa at the circuit 
breaker before draining the hot tub.  Do not turn power back on until your spa has been 
refilled with water. 
There are certain precautions to keep in mind when draining your hot tub.  If it is 
extremely cold, and the hot tub is outdoors, freezing could occur in the plumbing or the 
equipment.  On the other hand, if it is hot outdoors, do not leave the hot tub’s surface 
exposed to direct sunlight for long periods. 

 

DRAINING YOUR SPA 

 

¾

 

Trip all GFCI breakers in sub-panel, main electrical panel or unplug your spa 

 

¾

 

Remove

 the equipment compartment access door. 

¾

 

Locate

 end of the drain hose bib and turn gate at hose bib to closed position. 

¾

 

Unscrew

 and remove the drain cap. 

¾

 

Attach

 drain hose to a garden hose and direct to an appropriate draining area, keeping the hose 

below the water line. Open gate at hose bib to begin draining. 

¾

 

After

 your hot tub is empty, clean the shell and filter cartridge. See

 “Spa Maintenance” and 

Surface care. 

 

¾

 

After

 cleaning, remove garden hose, close gate at hose bib, replace drain cap and put drain hose 

back in equipment compartment. 

¾

 

Follow

 the “Start-up Instructions” to refill your spa. 

 
Before draining, power must be turned off at the GFCI circuit breaker.  Within the equipment compartment, locate 
the drain hose bib.  Attach a garden hose to the hose bib; make sure the garden hose exit spout will drain away from 
hot tub toward a previously selected safe drain area, and open the shut off lever on the hot tubs hose bib.  Water will 
start to drain.  You can also siphon the water from the hot tub.  The drain faucet will not remove all the water.  You 
may have to remove a small amount of the water by hand, using a towel or plastic container. 
 
If you plan to store your tub for the winter, you must also use a wet-vac to clean out the water lines to ensure they 
are free of any water.  Water left in the lines might freeze and damage the lines and jets.  To adequately clean out 
the lines, place the wet-vac over each jet face for 10-15 seconds.  On the whirlpool jet, rotate it to the open position 
and vacuum for 10-15 seconds.  Remove the filter cartridge and do the same.  Also, let the water drain from the 
heater tube by loosening the spit-nuts on each side of the heater tube.  Also, remove drain plug located on the wet 
end of the pump.  Remember to re-tighten the split-nuts when completed and replace drain plug on the wet end of 
the pump.  Use the wet-vac to vacuum up any water that may have drained on to the hot tub floor. 

 
Note: damage caused by improper winterizing will not be covered under warranty.  You will want 
to contact a professional for proper winterizing. 

 
 
 
 

Summary of Contents for ESPIRIT






















Reviews: