manualshive.com logo in svg

Fanimation Volare FP4210 Series, Owner'S Manual

Share
Download
Fanimation Volare FP4210 Series Owner'S Manual Download Page 12

12

Parts List

Model #FP4210**

Ref. #

Description

Part #

1

Hanger Bracket Assembly

APG510BL

2

Downrod/Hanger Ball Assembly Containing:

ADR6

¾¾

2a

Hanger Ball Assembly

2b

Downrod

2c

Hairpin Clip

2d

Clevis Pin

3

Ceiling Canopy

PG160

¾¾

4

Upper Housing Cover

P4274

¾¾

5

Fan Motor/Housing Assembly

AMA4210

¾¾

6

Adapter Plate with set screw

P4250

¾¾

7

Downlight Support Plate Assembly

AP4285-40

8

Lower Glass - twist on

P4245

¾¾

9

Blade Arm (Set of 5)

AP4266

¾¾

10

Volare Blade (Set of 5)

AP4290

¾¾

11

Hand-Held Remote Control

C20

12

Receiver Unit

RECAN68

13

Support Cable Bag Containing:

HDWFP4210

¾¾

Ceiling Support Cable

Cable Clamp

Flat Washer

Lag Bolt, 

3

/

8

˝

 x 2

˝

Hardware Bag Containing:

5

/

32

˝

 Threaded Rods (2)

5

/

32

˝

 External Lockwasher (2)

Knurled Knobs (2)

Flat Washer

Screw with spring washer,

 

5

/

32

-32 x 

3

/

8

˝

 (4)

-Upper Cover to DR Support

Screw with spring washer,

 

5

/

32

-32 x ¼

˝

 (4)-

D/L Plate to Adapter Plate

Blade Balance Kit (BALKT)

Allen Wrench

Wire Connectors (4)

Blade Holder Mounting Hardware Bag Containing:

¼-20 x

 

½

˝

 Phillips Head Screws (11)

Phillips Screwdriver, 4

˝

Blade Mounting Hardware Bag Containing:

10-32 Locking Hex Nut (16)

Flat Washer (16)

Before discarding packaging materials, be certain all parts have been removed

¾¾

Insert FINISH CODES (Refer to fan model number located on downrod support)

How To Order Parts

Contact your retail store for repair parts.

When ordering repair parts, always

give the following information.

• Part Number

• Part Description

• Fan Model Number

Summary of Contents for Volare FP4210 Series















Reviews:

No comments

Brands by name

Popular brands

Load more brands