background image

CHAPTER 6

CHAPTER 6

Maintenance & Technical Support

1.

Care & Maintenance

Falcon

®

SG Series UPSs are designed to be maintenance-free. They can be

cleaned with a damp cloth or non-abrasive cleanser, providing the UPS is 
turned off and the input plug is disconnected from the utility source.
On a regular basis, check the vents to make sure they are kept free from 
accumulation of dust, dirt or lint.

2.

Battery Life vs. Temperature

For full battery life, keep the UPS close to an ambient temperature of 77ºF. 
The batteries should never be exposed to temperatures below 40ºF and above 
104ºF.

3.

Battery Replacement

This UPS contains sealed maintenance-free batteries (VRLA).  When situated in 
a typical office environment, with the proper charging and limited cycling, the 
batteries can last many years. 

In home, office or computer room 

environments, the batteries should be replaced every three to five years.

Should you require battery replacement, contact the Falcon Service Department

(see page 21 for contact information).

Never attempt to service batteries.  High voltage exists within the unit, which 
could cause electrical shock.  

Servicing of batteries should be performed or 

supervised by personnel knowledgeable of batteries and the required 
precautions

.  Keep unauthorized personnel away from batteries.  

When replacing the UPS batteries, use the same number and type of batteries.

a. 

NEVER

dispose of batteries in a fire, as batteries will explode.

b. 

NEVER

dispose of used batteries or the UPS in the trash or landfill as it is 

against federal and state laws. 

The UPS and Batteries must be recycled. 

For UPS and battery recycling information, please contact our service 

department for the name and address of the nearest battery recycling facility. 

a. Do not open or mutilate the battery or batteries.  Released electrolyte is 
harmful to the skin and eyes.  It may be toxic.
b. A battery can present a risk of electrical shock and high short circuit current.  

REFER ALL BATTERY SERVICING OR REPLACEMENT TO A QUALIFIED 
SERVICE TECHNICIAN. NEVER ATTEMPT TO REPLACE THE BATTERIES  
YOURSELF.

WARNING

NEVER

CAUTION

19

Summary of Contents for SG1.5K-1T




























Reviews: