49
WARNING - SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
6. To Remove a Thermostat
Disconnect from the electricity supply.
Remove control panel and hotplate (see 1 & 2). Open
oven door. Remove oven furniture and slide out oven
roof liner if fitted.
For RH oven, remove thermostat phial cover (2 screws).
Unclip the thermostat phial from the clips in the oven
back.
For LH oven pull cooker forward to gain access to the
cover box at the rear of the cooker. Remove the four
screws securing the cover and lift clear.
Feed the thermostat capillary out of the oven.
Disconnect wiring from thermostat. Remove 2 screws
holding thermostat to mounting panel. Fit new
thermostat and reassemble in reverse order. Ensure
that the phial is clipped to the oven back with the phial
centrally positioned between the clips.
Check operation of thermostat.
7. To Change Grill Controller
Disconnect from the electricity supply.
Remove the control panel and hotplate (see 1 & 2).
Disconnect wiring from controller. Remove 2 screws
holding controller to mounting panel. Fit new controller
and reassemble in reverse order. Check for correct
operation.
BEFORE SERVICING ANY GAS CARRYING
COMPONENTS TURN OFF GAS SUPPLY.
8. To Change Hotplate Control Taps
Disconnect from the electricity supply.
Remove the control panel and hotplate (see 1 & 2).
Unplug the FSD lead from the rear of the tap. Undo
compression fitting at the rear of the tap. Remove the
fixings that secure the tap to the gas rail. Remove the
tap. Remove and discard the gasket seal. Fit new gasket
seal to replacement tap. Re-assemble in reverse order.
Check the appliance is gas sound. Check hotplate
ignition.
9. To Change Hotplate Burner Injector
Remove burner cap and head. Remove old jet. Fit new
injector. Reassemble in reverse order. Check appliance is
gas sound.
10. To Change Hotplate Burner Electrode
Lift off pan supports, remove burner cap. Remove the
screw holding the electrode. Pull electrode vertically
up sufficiently to grip the lead between thumb and
forefinger. Pull off the electrode, but keep hold of the
lead. Fit new electrode to the lead. Fix electrode in
burner with screw. Replace burner cap. Check the burner
ignition. Replace pan supports.
11. To Remove or Change a Hotplate Burner.
Remove the hotplate tray (see 2).
The burners except the right hand wok burner
are mounted on support struts. For these burners,
disconnect the burner feed pipes at the burner. Remove
the screws at the front and rear holding the support
struts. Lift the strut and burners clear. The burners are
fixed to the support struts with 2 screws. Remove the
appropriate burner and fit the new one. Reassemble in
reverse order. Check burner operation is satisfactory.
RH Wok burner
Disconnect the burner feed pipes at the burner. Fit the
new one and reassemble in reverse order. Check burner
operation is satisfactory.
12. To Remove an Oven Door
Open oven door. Support the door and remove the
two screws securing the upper hinge and gasket to the
cooker front. Remove the door from the lower hinge by
lifting slightly and moving outwards.
Reassemble in reverse order.
13. To Change Oven Door Outer Panel
Move the cooker forward to gain access to the sides.
Open the oven door slightly and remove the front panel
fixing screws from the door sides (two each side).
Carefully lift off the outer door panel.
Remove door handle from panel by unscrewing 2
retaining nuts. Fit door handle to new panel
Fit panel to door. Reassemble in reverse order.
14. To Change Oven Door Latch
Remove outer door panel (see 13). Remove screws ‘B’
holding latch assembly to inner door panel. Fit new
catch and reassemble in reverse order.
Check correct door operation.
