33
WARNING SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity before servicing. Check appliance is safe when you have finished.
RH Wok burner
Disconnect the burner feed pipes at the burner. Fit the
new one and reassemble in reverse order. Check burner
operation is satisfactory.
14. To Remove an Oven Burner
Open oven door and remove oven furniture. Remove
securing screw at the right hand end. The burner is held in
place by dimples in the mounting bracket. Slide the burner
to the left and lift up taking care not to disturb or damage
the two electrodes.
Reassemble in reverse order. Check the two electrodes have
not been disturbed.
15. To Change Oven Burner Assembly
Open oven door. Disconnect the tube nut and tubing.
Remove screw holding the oven burner assembly and
withdraw complete assembly. Remove oven burner
Fit oven burner to new assembly. Replace complete
assembly in the oven. Reconnect tube nut.
Check appliance is gas sound. Check correct fl ame save
guard device operation
16. To Change Oven Burner Injector
Remove the oven burner (see 14). The injector is now
accessible. Remove the old jet and fi t the new one.
Reassemble in reverse order. Check the fl ame save guard
device probe has not been disturbed.
17. To Change an Oven Programming Flame
Safeguard unit.
Disconnect from electricity supply.
Pull cooker forward to gain access to the cover box at the
rear of the cooker.
See ‘Moving the Cooker’ in installation section.
Remove the screws securing the cover and lift clear. Pull off
all the leads to the PFS control unit noting their positions.
Slacken the 3 screws holding the control unit to the cooker
and remove.
Fit new PFS unit to cooker and replace leads. Reassemble in
reverse order. Refer to wiring diagram. Check performance.
18 To Change Oven Solenoids
Disconnect from electricity supply.
Move the cooker forward to gain access to the rear. See
‘Moving the Cooker’ in installation section.
Remove the screws securing the cover and lift clear.
Disconnect solenoid leads and remove earth lead from
earth screw. Unclip wires from cable ties.
Disconnect pipe tube nuts to solenoid unit. Unscrew the
locking nut from the end connector and remove solenoid
unit. Fit new unit to mounting bracket and fi x in place with
locking nut. Refi t tube nut connections.
Replace leads (refer to wiring diagram). Replace wires in
cable ties. Check appliance is gas sound. Refi t cover box.
Check for correct operation of solenoids.
19. To Change Oven Electrode
Disconnect from electricity supply.
Remove oven burner (see 14). Remove screw and nut
securing the electrode to the burner. Pull lead from back
of electrode and fi t to new electrode. Fit new electrode to
burner.
Reassemble in reverse order.
Check ignition.
20. To Remove Grill Door
Remove L H side panel (see 3). Remove the plinth (4 screws)
and the central vertical cover (5 screws). Remove the two
countersunk screws (1 each side) securing the grill hinge
arms to the front of the grill chamber.
NOTE:
The arms are spring tensioned. Carefully remove the
grill door. Retain the gaskets.
Reassemble in reverse order ensuring that the gasket is
fi tted between the hinge arm and the front of the grill
chamber.
21. To Remove an Oven Door
Open oven door. Support the door and remove the two
screws securing the upper hinge and gasket to the cooker
front. Remove the door from the lower hinge by lifting
slightly and moving outwards.
Reassemble in reverse order.
22. To Change Ignition Generator
Disconnect from electricity supply.
Pull cooker forward to gain access to the cover box at the
rear of the cooker. Remove the screws securing the cover
and lift clear. Pull off all the leads to the generator noting
their positions. Slacken the two screws holding generator to
cooker and remove generator.
Fit new generator to cooker and replace leads. Reassemble
in reverse order. Refer to wiring diagram. Check ignition
performance.
