32
WARNING SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity before servicing. Check appliance is safe when you have finished.
3. To Remove Side Panels
Disconnect from electricity supply.
Remove the Control Panel - see 1. Pull the cooker forward.
Remove the 4 retaining screws for each panel (1 at the front
base, 1 on the top and 2 at the rear).
Reassemble in reverse order.
4. To Remove Ignition or light Switch
Disconnect from electricity supply.
Remove the Control Panel - see 1.
NB. The old switch may be destroyed during removal.
Remove the old switch from its bezel by griping the switch
body behind the control panel and twisting sharply. The
switch bezel can then be removed by folding back its
locking wings and pushing forward. Fit the new bezel to the
control panel by fi rst lining up the raised key on its body
with the cutout in the control panel and pushing it in from
the front. Assemble the new switch to the bezel by lining up
the key sections and pushing home. Fit the new button by
pushing in from the front.
Replace Control Panel in reverse order and test for ignition.
5. To Remove Clock
Disconnect from electricity supply.
Remove the Control Panel (See 1). Pull off the timer control
buttons.
Remove the timer/mounting bracket assembly from the
control panel by removing the fi xing screws.
Remove the timer from its mounting bracket by depressing
the plastic lugs on the timer case, at the same time pulling
the unit forward.
Reassemble in reverse order. When replacing leads refer to
the wiring diagram. Check operation of timer.
BEFORE SERVICING ANY GAS CARRYING COMPONENTS
TURN OFF GAS SUPPLY.
6. To Remove a Thermostat
Disconnect from electricity supply.
Remove RH hotplate tray. (For L H oven remove L H side
panel (see 3).) Open appropriate oven door.
Unclip the thermostat phial from the clips at the front of
the oven roof. Disconnect tubing nut at rear of thermostat
and remove the screw(s) securing the thermostat to the
gas rail. Remove thermostat and gasket/seal. When fi tting
replacement thermostat use the new gasket/seal supplied.
Ensure that the capillary is clipped to the bracket at the
front of the oven roof.
Reassemble in reverse order. Check appliance is gas sound.
Check operation of thermostat.
7. To Change Grill Control Tap
Disconnect from electricity supply.
Remove the Control Panel - see 1. Lift up the RH hotplate
tray front (see 2). Undo the gas connection to rear of valve
and remove the screw(s) securing tap to gas rail. Remove
old tap, discard old gasket/seal. Fit new gasket/seal to new
tap.
Reassemble in reverse order. Check tap is adjusted for
correct gas. Check appliance is gas sound.
8. To Change Warmer Switch
Disconnect from electricity supply.
Remove RH hotplate tray. (see 2). Disconnect wiring
from Warmer switch. Remove 2 screws holding switch to
mounting panel, taking care not to lose the switch rotation
limiter. Fit new switch and reassemble in reverse order.
Check for correct operation.
10. To Change Control Taps
Disconnect from electricity supply.
Remove the Control Panel (see 1). Lift up the appropriate
hotplate tray front (see 2).
Undo compression fi tting at the rear of the tap. Remove the
fi xings that secure the tap to the gas rail. Remove the tap.
Remove and discard the gasket seal. Fit new gasket seal to
replacement tap. Re-assemble in reverse order. Check the
appliance is gas sound. Check hotplate ignition.
11. To Change Hotplate Burner Injector
Remove burner cap and head. Remove old jet. Fit new
injector. Reassemble in reverse order. Check appliance is gas
sound.
12. To Change Hotplate Burner Electrode
Disconnect from electricity supply.
Lift off pan supports, remove burner cap. Remove the
screw holding the electrode. Pull electrode vertically up
suffi
ciently to grip the lead between thumb and forefi nger.
Pull off the electrode, but keep hold of the lead. Fit new
electrode to the lead. Fix electrode in burner with screw.
Replace burner cap. Check the burner ignition. Replace pan
supports.
13. To Remove or Change a Hotplate Burner.
Disconnect from electricity supply.
Remove the hotplate tray (see 2).
LH hotplate burners
Remove heat shield (2 screws). The burners are mounted
in 2’s on cross supports. Disconnect the burner feed pipes
at the burners. Remove the screw on the right holding
the cross support. Slide the support to the right to release
in from the left hand location. Lift the cross support and
burners clear. The burners are fi xed to the cross supports
with 2 screws. Remove the appropriate burner and fi t
the new one. Reassemble in reverse order. Check burner
operation is satisfactory.
