Fagor FET 313, Instructions For Use Manual

Page: 8 / 44

8
EN 4 / PROGRAMMING YOUR MACHINE
•DETAILS OF THE OPTIONS
•Prewash
Specially designed for heavily soiled washing (mud, blood, etc.).
A specific initial agitation in cold water precedes a phase of heating to
30°C.
This agitation phase in cold water enables the particles soiling the washing
to be removed before the water is heated.
Important :
Detergent must be placed in the " " container in the products
box.
•Anti-creasing
This avoids the washing creasing and makes it easier to iron.
•Extra rinse
"Especially for sensitive and allergic skin": adds an extra rinse to the
washing cycle.
•Delayed start
You can delay the start of your programme by 1 to 19 hours so that
you can benefit from cheap rate electricity or to have the cycle finish
at a desired time.
To do this, select the time that must pass before the cycle starts by
pressing successively on button
(this is done hour by hour) and
then press ”Start/Pause” .
NB:
- Even if you forget to press the “Start/Pause” button after selecting
this option, your choice will still be accepted after a few seconds.
- The time remaining before the start of the cycle is counted down hour
by hour from 19 hours to 1 hour and then minute by minute from 59
minutes to 1 minute.
- Throughout the whole waiting period, the delayed start symbol is
displayed and the four elements light up in succession.
- At the end of the waiting period, the programme starts and the display
shows the duration of the selected cycle.
•Full drum stop
This function enables you to remove the washing from your machine
before the spin phase or to delay this phase with you washing remaining
in water to prevent creasing.
NB : When the machine is stopped
with the tub full of water, the display
shows alternately:
Then:
— If you want to drain after spinning, use the selector
to choose a
suitable spin speed for your type of washing.
The programme will end automatically.
— If you just want to drain, turn the selector
to “Drip Dry” (position
”100”).
•MODIFYING A WASHING PROGRAMME
•During programming:
Anything can be changed before the “Start/Pause” button is
pressed.
•After the cycle has started:
You can change the type of textile (for example, switch from “COTTON”
to “SYNTHETICS”, etc.). In this case, check that the options you previously
selected are still there.
You must confirm your new selection by pressing the “Start/Pause”
button .
The machine may then possibly drain off some of its water.
•Throughout the cycle:
Depending on your model, the following changes are possible without
pressing the “Start/Pause”
button .
— You can change the temperature for the same type of textile.
NB: If the temperature achieved by the washing cycle is higher than your
new selection, heating the water stops immediately and the cycle
continues.
— You can alter the spin speed throughout the cycle.
— You can select “Drip Dry” (100) and “Full drum stop” throughout
the washing phase.
— You can activate the “Extra rinse”
option until rinsing starts.
— You can deactivate all the options throughout the cycle provided
that their action has not already finished.
•During delayed start
:
— Any kind of programme modification is accepted during a delayed
start’s waiting period.
— You can alter the length of a delayed start
throughout the waiting
period before the cycle effectively starts.
NB :
-
During this period, selecting a new time cancels out the previous
selection. The new period selected is accepted based on the last selection
made.
- If you want to cancel the delayed start completely during this period,
first display “
19h ” using button . Then press the button again and
briefly press ”Start/pause” .
The cycle will start immediately.
- If you want to reduce the length of time of the delayed start, proceed
in the same way but do not press the ”Start/Pause”
button.
Your machine is then ready for a new setting.
— You can only activate the “Prewash”
and “Anti-creasing” options
during a delayed start’s waiting period.
•When the cycle is over:
When the screen shows “ - 0 - ”, you can programme a new cycle
without having to reset the selector to the “O” position.
For this, all you have to do is turn one of the selectors or press one of
the buttons.
The screen shows the duration of the programme selected.
The machine is then ready to be reprogrammed.
•AUTOMATIC SAFETY SYSTEMS
•Lid opening safety system:
As soon as washing commences, the lid on your machine is locked.
When the cycle is finished or when the machine has stopped with the
drum full of water, the lid unlocks.
If you have programmed a "Delayed start", the lid is not locked until
the waiting period is over and the cycle starts.
If you wish to open the lid during the cycle, press button
briefly
and wait 1-2 minutes for the safety system to unlock the lid.
Important :
Depending on when you wish to open the lid during the cycle,
this time delay may be a little longer because a cooling down period
may also have to be included.
In fact, to avoid your being severely burnt, the lid safety system will
not open during the cycle unless the temperature inside the machine
is below a certain threshold.
•Water safety system:
During operation, constant control of the water prevents any overflows.
•Spin safety system:
Your washing machine is fitted with a safety system that restricts the
spin when poor load distribution is detected.
In this case, your washing may be insufficiently spun. Redistribute
your washing in the drum and programme a new spin.
•Anti-foam system:
You machine can detect when too much foam is being produced during
spinning.
At such times, spinning stops and the machine drains.
The cycle then restarts, adapting the spin rates and possibly adding
an extra rinse.
5
1
A
3
5
5
5
2
2
A
A
5
3