Factory Cat Pilot 24'' EDGE Operating Instructions Manual Download Page 34

Page: 34 / 41

- 34 -

PILOT-OP-EN

SQUEEGEE BLADE KITS & COMPLETE SQUEEGEE ASSEMBLIES:

SQUEEGEE

SIZE

20'' DISK

DECKS

24''

EDGE

DECKS

26'' DISK

DECKS

28''

EDGE

DECKS

28'' DISK

DECKS

26'' Squeegee

Optional

30'' Squeegee

Standard

Optional

34'' Squeegee

Optional

Standard

SQUEEGEE

SIZE

GUM RUBBER

BLADE KIT

LINATEX

BLADE

KIT

URETHANE

BLADE KIT

COMPLETE
SQUEEGEE

ASSEMBLIES

26'' Squeegee

130-770G

130-770L

130-770U

130-7180

30'' Squeegee

150-770G

150-770L

150-770U

150-7180

34'' Squeegee

180-770G

180-770L

180-770U

180-7180

SQUEEGEE MATERIAL:

USED FOR:

LINATEX

Provides best wear and tear resistant. Not
designed for use with chemicals.

URETHANE

Provides best resistance when dealing with harsh
chemicals, oils, fuels, etc.

GUM

Provides best drying preformance on rough/grouted
fl oor types by sealing over irregularities.

NOTICE

Squeegee blade kits include (1) Rear Blade, (1) Front
Blade, and (2) Backup Wheels with hardware.

NOTICE

Squeegee Assemblies (complete) listed above all come
with Linatex blades.

NOTICE

Size is stamped into the top of the painted steel
squeegee body on all squeegee's.

NOTICE

The 26'' squeegee is designed for narrow aisles and may
not have the same water control around tight turns as
the large squeegees.

Summary of Contents for Pilot 24'' EDGE










































Search results

Summary of Contents for Pilot 24'' EDGE

Reviews:

Related manuals for Pilot 24'' EDGE

Brands by name

Popular brands

Factory Cat Pilot 24'' EDGE, Operating Instructions Manual

Search results

Summary of Contents for Pilot 24'' EDGE

Reviews:

Related manuals for Pilot 24'' EDGE

Brands by name

Popular brands